Quickie Sunrise Q300M Instructions For Use Manual Download Page 6

6

       Q300M

Rev.1.0

ENGLISH

1.0 Your Wheelchair 

We at Sunrise Medical want you to get the best out of 

your  wheelchair . This Owner’s Manual will familiarise 

you with the wheelchair and its features. It contains 

hints on everyday usage and general care in addition to 

information on the high quality standards which we adhere 

to and details about the guarantee. 
Your wheelchair should be delivered fully configured for 

your use; there are a wide range of components and 

adjustments available on the wheelchair . For further 

information about these you should contact your Sunrise 

Medical authorised dealer.
Your wheelchair will reach you in excellent condition 

having been personally inspected before leaving our 

factory. Following the guidelines for maintenance and 

cleaning your wheelchair will maintain its first class 

condition and give you complete satisfaction.

The wheelchair has been designed for use by an 

individual on a daily basis. It is suitable for both indoor 

and outdoor use. It is only intended for use as a pavement 

vehicle, but may also be used when crossing between 

pavements.
This wheelchair has been designed for a single occupant 

of limited mobility up to the weight of 140Kg (dependant 

on options chosen for your wheelchair). 

The user must have the cognitive, physical and visual 

ability to control the wheelchair safely on a maximum 

slope of 14% - 8°, (subject to wheelchair configuration). 

If you are in any doubt as to the suitability of the power 

wheelchair, contact your local Sunrise Medical approved 

supplier for clarification, prior to commencing use.
It is very important to read the relevant section of the 

owner’s manual when making any minor adjustments. 

Consult the Technical Manual or your local Sunrise 

Medical authorised dealer for more complex adjustments.
If you have any queries about the use, maintenance or 

safety of your wheelchair , please contact your local 

approved Sunrise Medical service agent. If you do not 

know of an approved dealer in your area or have any other 

questions please write or telephone:
Sunrise Medical

Thorns Road

Brierley Hill

West Midlands

DY5 2LD

Phone:  0845 605 66 88 

Fax: 

0845 605 66 89

www.SunriseMedical.co.uk

2.0 How to use this manual

2.1 Introduction

Please keep a note of your local service agent’s address 

and telephone number in the space below.

In the event of a breakdown, contact them and try to give 

all relevant details so they can help you quickly.

The wheelchairs shown and described in this manual 

may not be exactly the same in every detail as your own 

model. However, all instructions are still entirely relevant, 

irrespective of detail differences.

NOTE: 

• 

The manufacturer reserves the right to alter without 

notice any weights, measurements or other technical 

data shown in this manual. All figures, measurements 

and capacities shown in this manual are approximate 

and do not constitute specifications.

• 

Information regarding the continued safe use of your 

product, such as product safety notices or recalls (also 

known as FSN/FSCA Field Safety Notice/Field Safety 

Corrective Action) may be issued by Sunrise Medical 

as required. These can be accessed on the Sunrise 

Medical web site (Safety Notifications). The information 

will also be provided to the organisation who supplied 

your product in order that any required actions can 

be implemented. It is important that you keep this 

organisation updated with any changes in your contact 

details or if you no longer use this product. Please pass 

this manual on to any 2nd users of the product.

2.2 Guarantee

The guarantee form is included in the Sunrise Pack. 

Please fill in the relevant details and return to us to 

register your entitlement.

THIS GUARANTEE DOES NOT AFFECT YOUR LEGAL 

RIGHTS IN ANY WAY.

Sunrise Medical* provides a guarantee, as set out in the 

warranty conditions, for products to its customers covering 

the following.

Warranty conditions:

1.  Should a part or parts of the product require repair 

or replacement as a result of a manufacturing and/or 

material fault within 24 months, then the affected part 

or parts will be repaired or replaced free of charge. The 

warranty will only cover manufacturing defects.

2.  To enforce the warranty, please contact Sunrise 

Medical Customer Service with the exact details of the 

nature of the difficulty. Should you be using the product 

outside the area covered by the Sunrise Medical 

customer service agent, repairs or replacement will 

be carried out by another agency as designated by 

the manufacturer The product must be repaired by a 

Sunrise Medical designated Customer Service agent, 

(dealer).

Summary of Contents for Sunrise Q300M

















































































Reviews: