background image

15

EAGLE 700/1000/1400W - REV009A  

GB

WARNING:

 make sure the electrical power to the motor is 

switchd off when working manualli on the windlass. Carefully 
remove the chain or rope from the gypsy or the rope from 
the drum. 

Quick

®

 windlasses are manufactured with materials resistant to 

marine environments. In any case, any salt deposits on the outside 
must be removed periodically to avoid corrosion and damage to 
the equipment. The parts where salt may have built up should be 
washed thoroughly with fresh water.

Once a year, the drum and the gypsy have to be taken apart as 
follows:

GYPSY SIDE

Use the handle (1) to remove the gypsy cover (2); remove the top 
clutch cone (3); loosen the fixing screws (11) of the chain release (9) 
and remove it and pull off the gypsy (4). 

Clean all the parts removed to avoid corrosion, grease the shaft 
thread (17) and the gypsy (4) where the clutch cones rest (3) (use 
grease suitable for marine environment). 

DRUM SIDE

Use the handle (1) to loosen the bush (22); pull off the drum (21) 
clean all the disassembled parts and grease the shaft (17).

Remove any oxide deposits from the terminals of the electric motor 
and the reversing contactor unit; grease them. 

POS.

DESCRIPTION

CODE

8

Oil seal  

PGPRL4056800

9

Rope/chain stripper Eagle

MSN10RXR1000

10

Spring washer

MBG06X000000

11

Screw

MBV0514MXCE0

12

Screw

MBV0514MXE00

13

Nut

MBD06MXENC00

14

Base Eagle

SGMSC10R0000

15

Bearing

MBJ160080000

16

Crown gear

MSLCR1000000

17

Shaft

MSAR10199R00

18

Shaft key 

MBH0807060X0

19

Base flange

SGMSGR10A000

20

Screw

MBV0516MXSC0

21

Drum “AL” stainless steel

SPMSE10ALR01

22

Bush drum

SGMSDCPAL100

23

O-ring PGR031650000

24

Sensor

KNREEDCL0000

25

Gasket

PGBSR1000000

26

Bush

MSLBC2000000

27

Worm screw

MSLVT1000000

28

Thrust bearing

MBJ7205BE000

29

Internal circlip

MBAN5220Y000

30

Oil seal

PGPRL2552100

31A

Electric motor 700W 12V

EMF071200000

31B

Electric motor 700W 24V

EMF072400000

31C

Electric motor 1000W 12V

EMF101200000

31D

Electric motor 1000W 24V

EMF102400000

31E

Electric motor 1400W 12V

EMF141200000

31F

Electric motor 1400W 24V

EMF142400000

32

Key

MBH050515F00

33A

Motor casing watertight 700W

PCCCPM070000

33B

Motor casing 
watertight 1000-1400W

PCCCPM100000

34

Grommet 

PCGPMMR00000

35

Terminal board cover

PCCPPMMR0000

36

Screw

MBV02213AXSC

37

Bottom gasket

PGGPMFN00000

38

Bottom protec cover

PCCPPMFN0000

39

Cable outlet

PPM20B000000

40

Studs

MBP080608X00

41

Washer

MBR08X000000

42

Toothed washer

MBR08XDE0000

43

Nut

MBD08MXEN000

MAINTENANCE

Summary of Contents for E 1012 D





































Reviews: