LEVEL
STEP 1
TV/PROJECTOR location ~ POWER OUTLET
Wall Plate ~ (Female Receptacle)
Determine based on where the TV wall-mount will be installed, on which side, (above or below the mount) will be best suited for the
location of the TV power connection and not to interfere with the TV installation on the mount. ~ Measure height and width of TV to
keep the wall plate hidden behind the TV.
Source Equipment / Existing A/C Outlet location ~ POWER INLET
Wall Plate ~ (Male Plug)
Determine location on the wall near the source equipment or within 30 inches of an existing A/C outlet.
STEP 2
~REQUIRES 3 WIRE 12-2 or 14-2 TYPE UL approved electrical building wire for in-wall use.
(Not supplied)
~
STEP 3
~Follow the ELECTRCIAL WIRE CONNECTION label on the backside of the wall plates.~
Use the WIRE STRIP GAUGE etched on the backside of the wall plates; trim off the covering of the ends of the wires.
Push excess electrical wire back through rear opening of the BLUE box. Secure both wall plates with color - matched screws
.
STEP 4
A
The POWER OUTLET and POWER INLET plates can be installed either vertically or horizontally
~ Determine location on wall/ceiling between framing studs, with a stud-finder.
~ Trace a cut-line with the supplied cardboard template.
~ Level for proper alignment. ~ Cut on the lines, using a drywall saw or utility knife.
~ Route electrical building wire within wall/ceiling between the two cutouts.
~ Using a screwdriver, bend one tab OUT on the backside of the BLUE box, and insert electrical
wire. Have approximately 4 inches sticking out from the edge of the box.
~ Strip off 3 inches of the outer sheath of the electrical wire.
~ Insert the BLUE box into the wall opening. ~ Screw in the 2 silver screws to open the wall-wings
to secure the boxes to the wallboard. ~ Use a level for proper alignment.
POWER OUTLET
~ (Female Receptacle)
(A)
Using the tip of needle-nose pliers or the
“bend hole”
on a wire stripper, bend the
wire-end into a “J” shaped hook.
(B)
Hook the wire-end on the right “clockwise” side of the screw as shown.
Tighten the screws to each wire. ~ Check for proper wiring connections as labeled.
POWER INLET
~ (Male Plug)
*DO NOT BEND OR “J” THE END OF THE WIRES.
(C)
Insert each of the three wires straight into the WIRE INSERT HOLES located on
the end of the INLET.
Each hole aligns with a colored screw around the sides
.
Tighten the screws to each wire. ~ Check for proper wiring connections as labeled.
POWER INLET
~ Plug “female” end of the POWER CORD, onto the “male” plug of the POWER INLET.
~ Plug “male” plug of the POWER CORD into the existing A/C outlet or power surge protector.
THE SYSTEM IS NOW POWERED
NOTE
:
If the supplied POWER CORD is not long enough, DO NOT EXTEND THE SUPPLIED CORD with another extension cord.
Must use 3 prong-grounded, UL LISTED extension cord. DO NOT EXCEED 15 FEET IN LENGTH.
C
C
L
E
V
E
L
POWER OUTLET
CHECK FOR PROPER WIRING CONNECTIONS WITH AN OUTLET-TESTER BEFORE PLUGGING IN DEVICE.
The HDTV is now ready to plug in, enjoy your wall-mounted system!
B
Quest Technology Int'l, Inc.
, intend to make this manual accurate and complete. However,
Quest Technology Int'l, Inc.
, makes no claim that the information contained herein covers all
details, conditions, or variations. Nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject
to change without notice or obligation of any kind.
Quest Technology Int'l, Inc.
, makes no representation of warranty, expressed or implied, regarding the information contained herein.
