Quectel M12 Hardware Design Download Page 53

Page: 53 / 76

M12 Hardware Design

M12_Hardware_Design_V3.3

- 52 -

Module

SIM_VDD

SIM_RST

SIM_CLK

SIM_DATA

SIM_PRESENCE

22R

100nF

SIM_Holder

GND

ESDA6V8V6

33pF

33pF 33pF 33pF

GND

VCC

RST

CLK

VPP

GND

Figure 34: Reference circuit of the 6 pins SIM card

In SIM interface designing, in order to ensure good communication performance with SIM card,

the following design principles should be complied with.



Place the SIM card holder close to module as close as possible. Ensure the trace length of

SIM signals do not exceed 200mm.



Keep the SIM signals far away from VBAT power and RF trace.



The width of SIM_VDD trace is not less than 0.5mm. Place a bypass capacitor close to SIM

card power pin. The value of capacitor is less than 1uF.



To avoid possible cross-talk from the SIM_CLK signal to the SIM_DATA signal be careful

that both lines are not placed closely next to each other. So each of SIM_DATA and

SIM_CLK line should be shield by ground. For good performance, the SIM_RST line also

should be protected by the ground.



In order to ensure good ESD protection, it is recommended to add TVS such as WILL

(http://www.willsemi.com) ESDA6V8AV6. The capacitance of ESD component is less than
50pF. The 22Ω resistors should be added in series between the module and the SIM card so

as to suppress the EMI spurious transmission and enhance the ESD protection. Note that the

SIM peripheral circuit should be close to the SIM card socket.



Place the RF bypass capacitors (33pF) close to the SIM card on all signals line for improving

EMI.

3.10.2. SIM

card

holder

For 6-pin SIM card holder, it is recommended to use Amphenol C707 10M006 512 2. Please visit

http://www.amphenol.com for more information

Quectel

Confidential

Summary of Contents for M12













































































Search results

Summary of Contents for M12

Reviews:

Related manuals for M12

Brands by name

Popular brands

Quectel M12, Hardware Design

Search results

Summary of Contents for M12

Reviews:

Related manuals for M12

Brands by name

Popular brands