background image

GL502MG User Manual

 

QSZTRACGL502MGUM0100

                                                                                                 

          12

 

8.

 

FCC Statement 

This  equipment  complies  with  FCC  radiation  exposure  limits  set  forth  for  an  uncontrolled 

environment. This equipment should be installed and operated with minimum distance of 20 cm 

between  the  radiator  and  your  body.  This  transmitter  must  not  be  co-located  or  operating  in 

conjunction with any other antenna or transmitter. 

 

This  device  complies  with  part  15  of  the  FCC  rules.  Operation  is  subject  to  the  following  two 

conditions:  (1)  this  device  may  not  cause  harmful  interference,  and  (2)  this  device  must  accept 

any interference received, including interference that may cause undesired operation. 

 

NOTE: 

The  manufacturer  is  not  responsible  for  any  radio  or  TV  interference  caused  by 

unauthorized modifications to this equipment. Such modifications could void the u

ser’s authority 

to operate the equipment. 

 

NOTE:

 This equipment has been tested and found to comply with the limits for a Class B digital 

device, pursuant to part 15 of the FCC Rules.    These limits are designed to provide reasonable 

protection  against  harmful  interference  in  a residential  installation.    This  equipment  generates 

uses and can radiate radio frequency energy and, if not installed and used in accordance with the 

instructions,  may  cause  harmful  interference  to  radio  communications.    However,  there  is  no 

guarantee  that  interference  will  not  occur  in  a  particular  installation.    If  this  equipment  does 

cause harmful interference to radio or television reception, which can be determined by turning 

the  equipment  off  and  on,  the  user  is  encouraged  to  try  to  correct  the  interference  by  one  or 

more of the following measures: 

- Reorient or relocate the receiving antenna. 

- Increase the separation between the equipment and receiver. 

-Connect  the  equipment  into  an  outlet  on  a  circuit  different  from  that  to  which  the  receiver  is 

connected. 

-Consult the dealer or an experienced radio/TV technician for help 

- This device and its antenna(s) must not be co-located or operating in conjunction with any other 

antenna or transmitter. 

 

Queclink 

Confidential

Summary of Contents for GL502MG
















Reviews: