12/24VDC - Power supply
signal
IN4 -
Potential free / 100KΩ
input 4
GND - Power supply ground
signal
R - Output assigned to IN1
IN1 -
Potential free / 100KΩ
input 1
G - Output assigned to IN2
IN2 -
Potential free / 100KΩ
input 2
B - Output assigned to IN3
IN3 -
Potential free / 100KΩ
input 3
W - Output assigned to IN4
Flush RGBW Dimmer
ORDERING CODE
Z-WAVE FREQUENCY
ZMNHWD1
868,4 MHz
ZMNHWD2
921,4 MHz
ZMNHWD3
908,4 MHz
ZMNHWD4
869,0 MHz
ZMNHWD5
916,0 MHz
ZMNHWD8
865,2 MHz
Qubino Flush RGBW module is used to control
RGB/RGBW strips and LED strips or bulbs to
create countless colour options and has 5 special
scene effects. It can also control halogen lights
and fans. Its extremely small size allows for easy
installation behind wall sockets and switches.
Controlled devices may be powered by 12 or 24
VDC. All IN and OUT terminals may be user
configured for LED control or 100 kΩ signal
readouts.
Supported control types
Push button (mono stable switch)
Bi stable switch
Before the installation disconnect power
supply (12-24VDC)
Connect the module according to electrical
diagram.
Pull the antenna out of the holder
Locate the antenna far from metal elements
(as far as possible).
Do not shorten the antenna.
Danger of electrocution!
Module installation requires a great degree of
skill and may be performed only by a qualified
and licensed electrician.
Even when the module is turned off, voltage
may be present on its terminals. Any works
on
configuration
changes
related
to
connection mode or load must be always
performed by disconnected power supply
(disable the fuse).
Note!
Do not connect the module to loads exceeding
recommended values. Connect the module only in
accordance to the below diagrams. Improper
connections may be dangerous.
Warning!
Rapid light changes may potentially trigger
seizures for people with photosensitive epilepsy.
R.G.B.W. Color LED Dimmer
1x User Manual
Notes for diagram:
1. Connect the R.G.B.W. Color LED Dimmer
according to wiring diagram.
- First, connect RGBW strip, outputs (R,G,B,W)
RGB/RGBW/LED
diodes, halogen lights, or inputs (IN1~IN4).
- Second, connect the power supply.
If the device is properly connected, the RGBW
strip will blink once. Note that the device must
be powered by a dedicated stabilized power
adapter
2. In the status of the factory default (Not
Paired), the red light and green light will blink
by turns, eg. red, green, red, green, etc..
3. Include the R.G.B.W. Color LED Dimmer into
the Z-wave network, press service button.
3 times in 2 seconds. If the device is properly
included, the green light will remains on.
4. Exclude the Flush RGBW Dimmer into the Z-
Wave network, press 3 times in 2 seconds. If
the device is properly excluded, the green light
will blink and the data will be reset to the
factory default values.
5. Please pull out the antenna and keep it at 90
degree to enahnce the RF signals.
6. Support auto inclusion: Install the device,
connect with the power, and the auto
inclusion function will work in about 2
minutes.
7.
Support remote exclusion: Through
configuration setting. Please refer to the following
table.
ID
Size
Value
240
1 byte
1
Warning!
1. The RGBW Controller is suggested to
operate in low voltage circuits of 12VDC
or 24VDC. Connecting higher voltage
load may result in the RGBW Controller
damage.
Please refer to the following table.
Current of RGBW Strip
Stranded Wire
High current
18 AWG
Low current
22 AWG
2. The RGBW Controller must be powered by the
same voltage
as the connected light source. I.e. if
controlling 12V LED strip, the module
must be connected to 12V power supply.
Similarly, if controlling 24V RGBW strip,
the RGBW Controller must be powered by
24V voltage supply.
3.
The RGBW Controller has 100KΩ input. There
is no 100KΩ
output. Output is controlled by PWM at 488Hz.
4. The RGBW Controller must be powered by
12VDC or 24 VDC stabilized power supply
with outputs load capacity matched to loads
voltage.
5. In case of connecting long
RGBW/RGB/LED strips voltage drops may
occur, resulting in lower light brightness
further from R/G/B/W outputs. To eliminate
this effect it's recommended to connect
few shorter strips in parallel connection
instead of one long strip connected
serially.
Maximum recommended wire length,
used to connect R/G/B/W outputs with a
RGBW/RGB/LED strip is 10 m. Observe
connected loads manufacturer
recommendations towards connection
wire diameter.
6. For connection of IN1~IN4, it is suggested
that you connect the 4 inputs individually to
the same type of deivce. The devices can be
as follows: the rotary swtich, the toggle switch,
or the push switch.
7. When the Controller is damaged or lost, and
you have already transferred the control
function to an external control switch before,
the product can be normally operated. In
other case, please purchase a
new Controller, press the Include/Exclude
Button three times to exclude the device, and
then include the device with the original
installation steps, the device can be restored
to normal operation. Please note that re-
including the product will reset the data to the
default values. Use
this procedure only in the event that the
network primary controller is missing or
otherwise inoperable.
Glossary of terms
Include/Exclude Button - Inclusion/exclusion, press
3 times in 2 second.
Parameter no. 1
– Input switch type
Available config. parameters (data type is 1 Byte
DEC):
default value 1
1 - bi-stable switch type
2 - mono stable (push button) switch type
NOTE: Please power cycle the device when
parameter is changed.
Parameter no. 2
– Switch mode
Available config. parameters (data type is 1 Byte
DEC):
default value 1
1 - Normal Mode
2 - Brightness Mode
3 - Rainbow Mode
NOTE: Using this parameter, it is possible to
select various modes of RGBW Dimmer
operation.
Parameter no. 3
– Auto scene mode set
Available config. parameters (data type is 1 Byte
DEC):
default value -
1 - Ocean
2 - Lightning
3 - Rainbow
4 - Snow
5
– Sun
NOTE: Activation of the programmed scene
changing color shades.
Parameter no. 4
– Auto scene duration
Available config. parameters (data type is 1 Byte
DEC):
default value 3
1 - 127 delay duration is from 1s to 127s
128 - 255 delay duration is from 1min. to
127min.
NOTE: Using this parameter, it is possible to
change Auto scene mode duration
Associations
The Module can be set 1 auto-report ID in Group
1.
The Module will send BASIC_REPORT to device
associated in Group 1 when correspond Device
is activated.
LED indication
Status
LED Signal
Remark
Not Paired
Solid Red
Paired up
Solid Green
Inclusion
Blinking Green
(Interval: 1
sec.)
Touch three times (Must
release
in 2 sec.)
Exclusion
Blinking Green
(Interval: 1
sec.)
Touch three times (Must
release
in 2 sec.)
Auto
inclusion
Blinking Green
(Interval: 1
sec.)
Connect/disconnet power to
connect with Z-wave
network
Hardware
button
1. Add device
2. Delete device
3. Restore to defult value
4. Set association
Input (I1~I4)
Control RGBW
channel(I1:R ~I4:W)
Input type
Remark
Momentary
Monostable or push button switch
Toggle
Bistable switch
Toggle w/Memory
ON:
Active for closing terminals
OFF:
Active for opening terminals
Input operating
mode
Remark
Normal
Each given switch key assigned to
one output channel
Brightness
All channels are controlled together
Rainbow
Transition through all colours
spectrum
(Operates on RGB
channels only)
The RGBW Controller may control:
• 12 / 24VDC powered RGB strips
• 12 / 24VDC powered RGBW strips
• 12 / 24VDC powered LED strips, bulbs, etc.
• 12 / 24VDC powered halogen lights
Additional features:
• 100KΩ sensors signal readouts
Electrical Diagram
Device Application
Introduction
Installation
Package Contents
Product Overview
Module Inclusion (Adding to Z-Wave
Network)
Configuration Parameters
