Quatech Device Server User Manual Download

Page: 64 / 98

Configuring the SDS using a Web interface

Quatech SDS User’s Manual

Page 58

940-0183-154

October 2006

Step

Procedure

Description

Step 4 (non-MEI) / Step 5 (MEI) applies to all units

Step 4

(non-MEI)

Step 5

(MEI only)

Repeat the steps above for each port you
need to configure and then press Save to

implement all of your changes.

Close and re-open the port to activate
your changes.
That’s it! You’re done. Normal is the

most common operating mode and the
easiest to set up.

Setting Tunneling operating mode parameters

Serial Tunneling allows two SDS units to create a virtual cable

connection between each other’s serial ports with one end configured

as a master and the other end as a slave. You set up the master with
the slave’s IP address and serial port number that you want use for

the virtual connection. The master finds the slave and makes the

connection. The master configures the slave’s parameters (baud rate,
parity, and so forth) as necessary. A master can connect either to an

SDS in Normal mode or to a slave in Tunneling mode.

On the slave end, all you have to do is click Slave and leave the rest of

the Operating Mode settings blank. The slave waits for a master to

connect to it and to provide the configuration parameters.

A master connects to one of a slave’s serial ports. A second master can

connect to another port on the slave at the same time. However, you

can only have one Tunnel master/slave combination working at the
same time between any single set of ports.

Step

Procedure

Description

Preliminary

Step

Select Serial Ports from the selection

bar.

Note: Setup screens vary slightly between
RS-232 and RS-232/422/485 (MEI) units.
If you have an RS-232/422/485 (MEI) SDS,

the Configure Serial Port Interface step will

display so that you can select between RS-
232 and RS-422/485 operation.
If you have an RS-232 SDS, the Configure

Serial Port Interface step will not display
and you will not be presented with any RS-
422/485 configuration options.

The Serial Port Setup screen shown on

the following page displays.

Note: Click on a link to see a pop-up help
screen for that item. For example, if you
click on the Tunnel Slave link, the
following help screen pops up.

Note: In Tunneling, a master
configures a slave so that the
slave can communicate with it.

Note: A Tunnel master needs to
know the slave’s IP address
and serial port number.

Summary of Contents for Device Server



































































































Search results

Summary of Contents for Device Server

Reviews:

Related manuals for Device Server

Brands by name

Popular brands

Quatech Device Server, User Manual

Search results

Summary of Contents for Device Server

Reviews:

Related manuals for Device Server

Brands by name

Popular brands