background image

Quantum Corp. (NYSE: QTM) is the leading global storage company 
specializing in backup, recovery and archive. Combining focused 
expertise, customer-driven innovation, and platform independence, 
Quantum provides a comprehensive range of disk, tape, media, and 
software solutions supported by a world-class sales and service 
organization. As a long-standing and trusted partner, the company works 
closely with a broad network of resellers, OEMs, and other suppliers to 
meet customer’s evolving data protection needs.

For assistance contact Quantum Technical Assistance center:

North America

+1-800-284-5101

UK, France, and Germany

00800 4 QUANTUM

EMEA

+44 1256 848 766

For worldwide support: 

www.quantum.com/contactsupport

Backup. Recovery. Archive. It’s What We Do.

©2007 Quantum Corporation. All rights reserved. Quantum, the Quantum logo, and all other 
logos are registered trademarks of Quantum Corporation or their respective owners.

81-81667-02 A01 August 2007

SuperLoader™ 3A Series Quick Start Guide

*81-81667-02 A01*

81-81667-02 A01

After the Installation

From the front panel of the autoloader, use the menus to set the IP address (DHCP or 

Static), Subnet Mask (if required), Gateway (if required), SNMP Server (optional), and 

Time Server (optional). 
The default IP address is 

192.168.20.128

.

The default login and password for the On-board Remote Manager is 

guest

 and 

guest

.

For detailed information on the setup, operation, and administration of your system 

(including accessing and using the FTP file server), see the 

SuperLoader 3A Series User’s 

Guide

 (PN 81-81643) and the 

A-Series FTP File Server User’s Guide

 (PN 81-81800) on the 

documentation CD provided with your autoloader.

Summary of Contents for SuperLoader 3A Series















Reviews: