background image

Backup. Recovery. Archive. It’s What We Do.

©2010 Quantum Corporation. All rights reserved. Quantum, the Quantum logo, and all 
other logos are registered trademarks of Quantum Corporation or of their respective owners. 
Protected by Pending and Issued U.S. and Foreign Patents, including U.S. Patent No. 5,990,810.

For assistance, contact the Quantum Customer Support Center:
USA: 

800-284-5101 (toll free) or 949-725-2100

EMEA: 

00800-4-782-6886 (toll free) or +49 6131 3241 1164

APAC: 

+800 7826 8887 (toll free) or +603 7953 3010

Worldwide:  

http://www.quantum.com/ServiceandSupport

About Quantum

Quantum Corp. (NYSE:QTM) is the leading global storage company 
specializing in backup, recovery and archive. Combining focused 
expertise, customer-driven innovation, and platform independence, 
Quantum provides a comprehensive range of disk, tape, media and 
software solutions supported by a world-class sales and service 
organization. This includes the DXi™-Series, the first disk backup 
solutions to extend the power of data deduplication and replication 
across the distributed enterprise. As a long-standing and trusted 
partner, the company works closely with a broad network of 
resellers, OEMs and other suppliers to meet customers’ evolving 
data protection needs.

*6-66594-001*

18

6-66844-01 Rev A, January 2010

Product Name Quick Start Guide

Summary of Contents for LTO-3



















Reviews: