background image

Safety Instructions

6

QBOX-2080 Series User’s Manual

remove the component’s antistatic packing material until you are ready to install 

the component in a computer. Just before unwrapping the antistatic packaging, 

be sure you are at an ESD workstation or grounded. This will discharge any 

static electricity that may have built up in your body.

„

When transporting a sensitive component, first place it in an antistatic container 

or packaging.

„

Handle all sensitive components at an ESD workstation. If possible, use 

antistatic floor pads and workbench pads.

„

Handle components and boards with care. Don’t touch the components or 

contacts on a board. Hold a board by its edges or by its metal mounting bracket.

„

Do not handle or store system boards near strong electrostatic, electromagnetic, 

magnetic, or radioactive fields.

„

Instructions for Lithium Battery

WARNING

Danger of explosion when battery is replaced with incorrect type. Only replace 

with the same or equivalent type recommended by the manufacturer.

Do not dispose of lithium batteries in domestic waste. Dispose of the battery 

according to the local regulations dealing with the disposal of these special 

materials (e.g. to the collecting points for disposal of batteries)

„

Voltage Ratings

The external power adaptor of the QBOX-2080 Series has the following voltage 

ratings:

„

Input: 100-240 VAC, 50-60 Hz

„

Output: 60W, +12VDC/5.0A output

Summary of Contents for QBOX-2080 Series











































Reviews: