background image

Preface 

12 

KEEX-8100 Series Use r’s Manual 

area (domestic environment) is likely to cause harmful interference, in which case 
the user will be required to correct the interference (take adequate measures) at 
their own expense. 
Changes or modifications not expressly approved by Quanmax could void the user's 
authority to operate the equipment. 
 

NOTE  

The assembler of a personal computer system may be required to test 

the system and/or make necessary modifications if a system is found to 
cause harmful interference or to be noncompliant with the appropriate 

standards for its intended use. 

 

 

Warranty Policy 

Limited Warranty 

Quanmax Inc.’s detailed Limited Warranty policy can be found under Support at 
www.quanmax.com. Please consult your distributor for warranty verification. 
The limited warranty is void if the product has been subjected to alteration, neglect, 
misuse, or abuse; if any repairs have been attempted by anyone other than 
Quanmax or its authorized agent; or if the failure is caused by accident, acts of God, 
or other causes beyond the control of Quanmax or the manufacturer. Neglect, 
misuse, and abuse shall include any installation, operation, or maintenance of the 
product other than in accordance with the user’s guide. 
No agent, dealer, distributor, service company, or other party is authorized to change, 
modify, or extend the terms of this Limited Warranty in any manner whatsoever. 
Quanmax reserves the right to make changes or improvements in any product 
without incurring any obligation to similarly alter products previously purchased. 
 

Return Procedure 

For any Limited Warranty return, please contact Support at www.quanmax.com and 
login to obtain a Return Material Authorization (RMA) Number. If you do not have an 
account, send an email to [email protected] to apply for one. 
All product(s) returned to Quanmax for service or credit must be accompanied by a 
Return Material Authorization (RMA) Number. Freight on all returned items must be 
prepaid by the customer who is responsible for any loss or damage caused by 
common carrier in transit. Returns for Warranty must include a Failure Report for 
each unit, by serial number(s), as well as a copy of the original invoice showing the 

Summary of Contents for KEEX-8100 Series




























































Reviews: