background image

ANHUI QUANCHAI ENGINE CO., LTD

 

 

27. Hard to get diesel engine started 

 

 

Seque

nce 
No. 

Position 

tested 

Normal 

Abnormal 

Fuel tank 

There  is  sufficient  fuel  in  the  fuel  tank 

and the sediment cup is opened. 

Fill  in  diesel  and  turn  on  the 

switch. 

Fuel system 

There  is  no  air  in  the  fuel  system,  no 

water  in  the  fuel,  and  no  oil  leakage  at 

the joint. 

Discharge  air,  replace  diesel,  and 

tighten the joint. 

Oil  circuit  or 
filter 

The oil circuit and filter are unblocked. 

Clean  the  pipeline,  clean  or 

replace  the  diesel  filter  element, 

and clean the fuel inlet pipe of the 

fuel  supply  pump  and  its  filter 

screen. 

Fuel 

supply 

pump and fuel 
injection 
pump 

The  fuel  supply  pump  and  the  fuel 

injection  pump  work  normally,  and  the 

advance angle of fuel supply is correct. 

Check  whether  the  fuel  supply 

pump  and the  fuel  injection  pump 

work  normally,  and  adjust  the 

advance angle of fuel supply. 

Fuel injector 

The  fuel  injector  works  normally  while 

injecting fuel. 

Disassemble  and  repair  the  fuel 

injector, 

adjust 

the 

injection 

pressure  on  the  fuel  injector  test 

bench, and clean, repair or replace 

the  fuel  injector  fitting.  Replace 

the spring.  

Fuel  injection 
pump 

The fuel outlet valve and plunger fitting 

of  the  fuel  injection  pump  work 

normally without wear and tear. 

Grind, repair or replace parts. 

 

 

 

 

 

 

 

Summary of Contents for N485D












































































































































Reviews: