manualshive.com logo in svg

Quality Water Treatment Prosoft Elite, Installation Instructions Manual, Page: 2 / 9

Share
Download
Quality Water Treatment Prosoft Elite Installation Instructions Manual Download Page 2

 

Page 2 of 9 

 

Copyright © 2011 Quality Water Treatment, All right reserved. 

rev. 8/2/2011

                               www.qualitywatertreatment.com 

 

 

            

 

 
 

After adding the resin, remove the temporary cap, clean the valve threads with water, and screw 
the valve on. When screwing the valve on the tank the tube will slip into the bottom of the valve 
hole. Note no silicone or tape is needed, the valve is o’ring fit and only needs to be tightened by 
hand. 

MediaGuard KDF Filter Installation Guide: 

 

 
After adding the resin, remove the temporary cap, clean the valve threads with water, attach 
mediaguard filter to bottom of control valve then screw the control valve on to the tank as the 
mediaguard filter slides over the distributor tube inside the tank. Note no silicone or tape is 

needed, the valve is o’ring fit and only needs to be tightened by hand. 

 

 

 

Summary of Contents for Prosoft Elite










Reviews:

No comments