background image

ORIGINAL INSTRUCTIONS

300 Watt 

Electric Grass Trimmer

HELPLINE NO 0844 8010979

GENERAL POWER TOOL 

SAFETY WARNINGS

WARNING!

  When using the machine 

the safety rules must be followed. For 

your own safety and bystanders please 
read these instructions before operating the 
machine. Please keep the instructions safe 
for later use.

SAVE THESE INSTRUCTIONS

This grass trimmer is designed for cutting 
grass and similar soft vegetation and for 
trimming grass edges in private and hobby 
garden areas which are not accessible with 
a lawnmower.   
The device is not allowed to be used in 
public gardens, parks, sports centres or 
at roadsides as well as in agriculture and 
forestry.
This lawn trimmer is not allowed to be used 
for cutting or chopping: 
- Hedges, shrubs and bushes, 
- Flowers, 
- In terms of composting. 
Otherwise, there is a risk of injury.
This appliance is not intended for use by 
persons (including children) with reduced 
physical, sensory or mental capabilities, 
or lack of experience and knowledge, 
unless they have been given supervision or 
instruction concerning use of the appliance 
by a person responsible for their safety. 
Children should be supervised to ensure that 
they do not play with the appliance.
If the supply cord is damaged, it must be 
replaced by the manufacturer, its service 
agent or similarly quali

fi

ed persons in order to 

avoid a hazard.
a) Wear protective glasses or goggles;
b) Never allow children or people unfamiliar 

with the instructions to use the machine;

c)  Stop using the machine while people, 

especially children, or pets are nearby;

d) Only use the machine in daylight or good 

arti

fi

cial light;

e)  Before using the machine and after 

any impact, check for signs of wear or 
damage and repair as necessary;

f)  Never operate the machine with 

damaged guards or without the guards in 
place;

g)  Keep hands and feet away from the 

cutting means at all times and especially 
when switching on the motor;

h)  Take care against injury from any device 

fi

tted for trimming the 

fi

lament line length. 

After extending new cutter line always 
return the machine to its normal operating 
position before switching on;

i) Never 

fi

t metal cutting elements;

j)  Never use replacement parts 

or accessories not provided or 
recommended by the manufacturer;

k)  Disconnect the machine from the mains 

before checking, cleaning or working on 
the machine and when it is not in use;

I)  Always ensure that ventilation openings 

are kept clear of debris;

MAINTENANCE

a) After use, disconnect the machine from 

the mains and check for damage;

b) When not in use store the machine out of 

the reach of children;

c)  Mains powered trimmers should only be 

repaired by an authorised repairer;

d) Use only manufacturers recommended 

replacement parts and accessories. 

-  Read the instructions carefully,
-  Be familiar with the controls and proper 

use of the equipment;

-  Before use check the supply and 

extension cord for signs of damage or 
ageing,

-  If the cord becomes damaged during 

use, disconnect the cord from the supply 
immediately. DO NOT  TOUCH THE CORD 
BEFORE DISCONNECTING THE SUPPLY,

-  Do not use the lawn trimmer (edge 

trimmer), if the cords are damaged or 
worn.

WARNINGS:

WARNING:

 Cutting elements continue 

to rotate after the motor is switched 

off,
- Keep extension cords away from cutting 
elements;
It is recommended that appliances should 

Summary of Contents for GGT3001













Reviews: