background image

2

Unpacking: 

When unpacking, check to make sure all parts are included. If any part is missing or 
broken, please call Quadratec Customer Service at 800-745-6037 as soon as possible. 

Winch Assembly

Clutch 

Handle

Winch Power Button

Hawse Fairlead

Fairlead 

Hardware

Winch

 Mounting  Hardware

Remote 

Controller

Remote 

Cable

Winch Hook

Winch Hook Strap

Remote Control 

Plug Cover 

Winch 

Line  

A Few Words About Product Safety: 

Your safety and the safety of others is 
very important.  To help you avoid risks 
and make informed decisions this manual 
contains safety messages about your

 Q-Performance Series self-recovery 
winch. Individual safety messages 
and sections of this manual may be 
preceded by the safety alert symbol   

---- 

 

and one of three signal words:

A HAZARDOUS SITUATION WHICH, IF NOT AVOIDED, COULD RESULT IN DEATH 

OR SERIOUS INJURY. YOU CAN BE KILLED OR SERIOUSLY HURT IF YOU DO 

NOT FOLLOW INSTRUCTIONS.

A HAZARDOUS SITUATION WHICH, IF NOT AVOIDED, COULD RESULT IN 

MINOR OR MODERATE INJURY. YOU CAN BE MODERATELY HURT AND ALSO 

MAY SUFFER PROPERTY DAMAGE IF YOU DO NOT FOLLOW INSTRUCTIONS. 

CAREFUL ATTENTION IS REQUIRED TO THIS INSTRUCTION OR OPERATION BUT 

DOES NOT GENERALLY RELATE TO PERSONAL INJURY. DAMAGE TO YOUR 

QUADRATEC

®

 PRODUCT OR OTHER PROPERTY MAY RESULT IF YOU DO NOT 

FOLLOW INSTRUCTIONS.

Summary of Contents for 92122.4030

















Reviews: