background image

The Trusted Source

®

2

TO REDUCE RISK OF SERIOUS INJURY OR PROPERTY DAMAGE:
INSTALL ACCORDING TO INSTRUCTIONS. TORQUE AND RECHECK
FASTENERS AFTER 250 MILES AND FREQUENTLY THEREAFTER.
INSPECT AND DO NOT USE RECEIVER/RACK IF DAMAGED.

ALWAYS FOLLOW ALL SAFETY WARNINGS, CAUTIONS AND NOTICES
IN THE INSTALLATION INSTRUCTIONS AND DOCUMENTATION THAT
CAME WITH YOUR BIKE RACK. THIS DOCUMENT ONLY REFERS TO
BIKE RACK ASSEMBLY AND INSTALLATION. 

MAKE CERTAIN BICYCLES ARE PROPERLY SECURED BEFORE
DRIVING ON PUBLIC ROADS. FAILURE TO DO SO COULD CAUSE
PROPERTY DAMAGE OR PERSONAL INJURY.

Before You Begin Installation: 

Congratulations on your purchase of
Platform Mount Bike Rack for Wrangler
vehicles. When unpacking, check to
make sure all parts are included and
not damaged due to shipping.

If any part is missing or broken, please
call Customer Service at 800-745-6037
as soon as possible.

Regarding Bike Rack Safety: Always
check that the rack and bicycles are
securely mounted on your vehicle.
Failure to do so could cause property
damage or personal injury.  

Thank you again for your purchase
and let’s start the installation process.

a hazardous situation which, if not avoided, could result in death or
serious  injury.  You  CAN  be  KILLED  or  SERIOUSLY  HURT  if  you  don’t
follow instructions.

a hazardous situation which, if not avoided, could result in minor or
moderate injury. You CAN be moderately HURT and also may suffer
property damage if you don’t follow instructions. 

Careful attention is required to this instruction or operation but does
generally  not  relate  to  personal  injury.  Damage  to  your  Quadratec

®

product or other property may result if you don’t follow instructions. 

A Few Words About Product Safety: 

Your Platform Mount Bike Rack is
intended to enhance the utility and
enjoyment of your off road capable
vehicle. Before installation, please take a
moment to review the following safety 

information and installation instructions
Important safety information is gener-
ally preceded by one of three signal
words indicating the relative risk o

injury.  The signal words mean:

Q_PLATFORM_RACK_INST_A4.qxp_A4  6/10/19  3:52 PM  Page 2

Summary of Contents for 92034.1008









Reviews: