background image

2

READ ALL SAFETY MESSAGES AND ALWAYS WEAR 

SAFETY GLASSES WHEN WORKING WITH TOOLS.

A HAZARDOUS SITUATION WHICH, IF NOT AVOIDED, COULD RESULT IN DEATH OR 
SERIOUS INJURY. YOU CAN BE KILLED OR SERIOUSLY HURT IF YOU DON’T FOLLOW 
INSTRUCTIONS.

A HAZARDOUS SITUATION WHICH, IF NOT AVOIDED, COULD RESULT IN MINOR 
OR MODERATE INJURY. YOU CAN BE MODERATELY HURT AND ALSO MAY SUFFER 
PROPERTY DAMAGE IF YOU DON’T FOLLOW INSTRUCTIONS. 

CAREFUL ATTENTION IS REQUIRED TO THIS INSTRUCTION OR OPERATION BUT 
DOES GENERALLY NOT RELATE TO PERSONAL INJURY. DAMAGE TO YOUR PRODUCT 
OR OTHER PROPERTY MAY RESULT IF YOU DON’T FOLLOW INSTRUCTIONS. 

A Few Words About Product Safety: 

Your Quadratec

®

 Tube Doors enhance 

the look, visibility, and performance of 
your off-road capable vehicle. Before 
installation, please review the following 
safety information and installation 
recommendations.

Throughout these instructions import-
ant safety information is generally 
preceded by one of three signal words 
indicating the relative risk of injury, 
property damage or adverse conse-
quence. The signal words mean:

Before You Begin Installation: 

Congratulations on your purchase. 
When unpacking, check to make sure 
all parts are included and not damaged 
due to shipping. If any part is missing or 

broken, please call Customer Service 
at 800-745-6037 as soon as possible.
Thank you again for your purchase 
and let’s start the installation process.

THESE DOORS ARE NOT INTENDED TO PROTECT OR CONTAIN THE 

VEHICLE OCCUPANTS OR PREVENT INJURY OR DEATH IN THE EVENT 

OF AN ACCIDENT.

WEAR SEAT BELTS AT ALL TIMES.

ALWAYS READ ALL INSTRUCTIONS COMPLETELY AND FOLLOW 

ALL VEHICLE MANUFACTURER WARNINGS AND GUIDELINES.

PERIODICALLY CHECK AND ADJUST ALL LATCHES AND FASTENERS, 

FAILURE TO DO SO COULD RESULT IN THE DOORS NOT LATCHING 

SECURELY.

Installation Instructions: 

Put on safety glasses. Start by removing 
your vehicle’s factory doors. Refer to 
your vehicles owner manual or visit 
the video section of our website: 
www.quadratec.com

Retain the factory door retaining nuts 
for use with your tube doors. Please 
note, the installation is the same for 
both versions regardless of which 
generation vehicle is shown. 

Summary of Contents for 11147.10 Series









Reviews: