background image

The Trusted Source

®

2

Before You Begin Soft Top Installation: 

Congratulations on your purchase of the
Adventure Top. This high quality soft
top is designed to provide years of pro-
tection from whatever nature can throw
at you! We have used only the finest
materials in creating this soft top but
like any product that is exposed to the
elements, there is some general mainte-
nance that is required to keep your top
looking like new. Please see page 19 for
these important maintenance tips as
well as pages 3-4 for the list of hardware
components. All of those parts will be
available as repair/replacement parts if
needed.

When unpacking, check to make sure all
parts are included. If any part is missing 
or broken, please call Quadratec 
Customer Service at 800-745-6037
as soon as possible.

Important: Make sure you become famil-
iar with the installation process of this
top by reading the following instruction
sheet thoroughly. 

Important: For a smooth fit and ease 
of installation, this top should be 
installed at temperatures above 72
degrees. Below this temperature, the
fabric may contract an inch or more
making it difficult to install. We
highly recommend taking the top 
out of the package and letting it sit 
inside a warm place or in direct sun
light for 1-2 hours before you install 
the top. When warm, this top will 
install quickly.

Important: Note that it is normal for the
fabric and glass to contract and wrinkle
when stored in the shipping carton. 
In a few days the fabric and glass 
will relax & wrinkles will disappear.

Thank you again for your purchase and
let’s start the installation process!

a hazardous situation which, if not avoided, could result in death or
serious injury. You CAN be KILLED or SERIOUSLY HURT if you don’t
follow instructions.

a hazardous situation which, if not avoided, could result in minor or
moderate injury. You CAN be moderately HURT and also may suffer
property damage if you don’t follow instructions. 

Careful attention is required to this instruction or operation but does
generally not relate to personal injury. Damage to your Quadratec

®

product or other property may result if you don’t follow instructions. 

A Few Words About Product Safety: 

Your QuadraTop Adventure soft top is
intended to enhance the utility and
enjoyment of your off road capable
vehicle. Before installation, please
review the following safety information
and installation recommendations.

Throughout these instructions impor-
tant safety information is generally
preceded by one of three signal words
indicating the relative risk of injury,
property damage or adverse conse-
quence. The signal words mean:

ADV_2DR_S_UPDATED.qxp_QTOP  5/23/17  11:44 AM  Page 2

05232017114838

Summary of Contents for 11113.1235





















Reviews: