background image

November 10, 2015 

 

 

 

           7061-197H 

 

 

 

         

                  3

Explorer II Medium Wood Stove

Model:

Explorer II Medium Wood Stove

Laboratory:

Intertek

Report No:

10126132PRT

Type:

Safety

Standard:

UL 1482-07; ULC S627-00

EPA Certification #: 925

EPA Certified Emissions: 2.2 grams per hour

*LHV Tested Efficiency: 78.3 %

**HHV Tested Efficiency: 72.4 %

***EPA BTU Output: 11,200 to 35,900 / hr.

****Peak BTU/Hour Output: 61,000

Vent Size: 6 inches

Firebox Size: 2.42 cubic feet

Recommended Wood Length: 20 inches

Fuel Orientation: Side-to-Side

Fuel Seasoned Cord Wood

* Weighted average LHV efficiency using Douglas Fir dimension-

al lumber and data collected during EPA emissions test.

**

Weighted  average  HHV  efficiency  using  Douglas  Fir  dimen-

sional lumber and data collected during EPA emissions test.

***

A range of BTU outputs based on EPA Default Efficiency and 

the burn rates from the low and high EPA tests, using Douglas 

Fir dimensional lumber.

****

A peak BTU out of the unit calculated using the maximum first 

hour burn rate from the High EPA Test and the BTU content of 

cordwood (8600) times the efficiency.

The Quadra-Fire Explorer Series Wood Stove (ACC) meets 

the U.S. Environmental Protection Agency’s crib wood emis-

sion  limits for wood heaters sold after May 15, 2015. 

This wood heater needs periodic inspection and repair for 

proper operation. It is against federal regulations to operate 

this wood heater in a manner inconsistent with operating 

instructions in this manual.

Important Safety Information

A...Appliance.Certification

NOTE:  Hearth & Home Technologies, manufacturer of 

this appliance, reserves the right to alter its products, their 

specifications and/or price without notice.

C...Mobile.Home.Approved.(USA.ONLY).

 • 

This appliance is approved for mobile home installa-

tions in the USA when not installed in a sleeping room 

and when an outside combustion air inlet is provided.

 • 

The structural integrity of the mobile home floor, ceil-

ing, and walls must be maintained. 

 • 

The appliance must be properly grounded to the frame 

of the mobile home with #8 copper ground wire, and 

chimney must be listed to UL103 HT or a listed UL-

1777 full length six inch (152mm) diameter liner must 

be used. 

 • 

Outside Air Kit, part OAK-ACC must be installed in a 

mobile home installation.

Improper  installation,  adjustment,  alteration,  service  or 

maintenance can cause injury or property damage. 

For assistance or additional information, consult a qualified 

installer, service agency or your dealer.

  • 

Installation and use of any damaged appliance. 

  • 

Modification of the appliance.

  • 

Installation other than as instructed by Hearth & Home

  

Technologies.

  • 

Installation and/or use of any component part not approved

   

by Hearth & Home Technologies.

  • 

Operating appliance without fully assembling all 

  

components.

  • 

Operating appliance without legs attached (if supplied with 

  

it).

  • 

Do NOT Overfire - If appliance or chimney connector glows, 

   

you are overfiring.

   Any such action that may cause a fire hazard.

WARNING

Fire.Risk.

Hearth & Home Technologies disclaims any 

responsibility for, and the warranty will be voided 

by, the following actions: 

B...BTU.&.Efficiency.Specifications

Hearth & Home Technologies WILL NOT warranty stoves 

that exhibit evidence of over-firing.  Evidence of over-firing 

includes, but is not limited to:

  •  Warped air tube

  •  Deteriorated refractory brick retainers

  •  Deteriorated baffle and other interior components

E..Non-Combustible.Materials

Material which will not ignite and burn, composed of any 

combination of the following: 

 

- Steel   

 

- Plaster

 

- Brick   

 

- Iron

 - 

Concrete 

 - 

Tile

 

- Glass   

 

- Slate

Materials reported as passing 

ASTM E 136, Standard 

Test.Method.for.Behavior.of.Metals,.in.a.Vertical.Tube.

Furnace.of.750°.C..

F..Combustible.Materials

Material made of/or surfaced with any of the following ma-

terials: 

 

- Wood  

 

- Compressed Paper

 

- Plant Fibers   

- Plastic

 

- Plywood/OSB   

- Sheet Rock (drywall)

Any material that can ignite and burn: flame proofed or not, 

plastered or un-plastered. 

D...Glass.Specifications

This stove is equipped with 5mm ceramic glass.  Replace 

glass only with 5mm ceramic glass.  Please contact your 

dealer for replacement glass.

Summary of Contents for XPLRMED-PBK





















Reviews: