STATIC NOTICE
Thermostat is protected against normal static electric
discharges, however to minimize the risk of damaging
the thermostat in extremely dry weather, please touch
a grounded metal object before touching the thermo-
stat.
Temperature Programs
The thermostat by default has 4 separate program events
they are: MORN, DAY, EVE, and NITE. Each event ends
at the start time of the following event.
NOTE: When the last event is finished for each day or
group of days, the thermostat will advance for-
ward into the next day or group of days.
6. Use steps 3 through 5 to set up the events for the rest
of the week or group of days.
7. Return the SET switch back to RUN.
N
OTE: If the thermostat is set for 2 events a day instead
of 4, the thermostat will only use the DAY and
NITE events.
SET TEMPERATURE PROGRAMS:
1. Move
TEMPERATURE
switch to HEAT.
2.
Move SET switch to TEMP PROG position.
3.
Starting with Monday, use the UP or DOWN buttons to
adjust the start time and set temperature for the MORN
event, and then press NEXT button to advance.
4.
Adjust the start time and set temperature of the DAY
event then press NEXT button.
5. Continue in this same manner to adjust the start time
and set temperatures for the EVE and NITE events for
Monday.
COPY PROGRAM FEATURE:
Using similar instructions as
SET TEMPERATURE PROGRAMS
the COPY button will allow a whole day of set program
events to be copied to another day.
1. Move
TEMPERATURE
switch to HEAT as well as
move SET switch to TEMP PROG position.
2.
Starting with Monday, use the UP or DOWN buttons
to adjust the start time and set temperature for the
MORN, DAY, EVE, and NITE events. Press the COPY
button and then press the NEXT button to advance to
Tuesday.
3.
With Tuesday displayed press COPY button. As
all programs events from Monday will be copied to
Tuesday (this will advance automatically to the next
day; Wednesday, as the word COPY will appear on
the screen for one second).
4.
Continue in this pressing COPY button to set desired
days with original setting.
NOTE:
The word COPY will not appear on the display
for Monday, but will display each day afterwards
for approximately one second and the day of the
week will automatically advance forward to the
next day.
Other Features
TEMPERATURE CALIBRATION:
The internal temperature sensor in this thermostat is accu-
rately calibrated at the factory, and in most cases altera-
tions to this setting should not be needed. The temperature
calibration feature allows you to manually offset the mea-
sured temperature by as much as plus or minus 5°F (3°C)
from its original value. If several thermostats are used in
the same house, this feature can be used to synchronize
this thermostat to the others.
Change the temperature calibration:
1.
Move TEMPERATURE switch to OFF.
2.
Move SET switch to RUN.
3.
Press and hold both UP and DOWN buttons together
for at least 5 seconds; the words SET and CAL will
appear on the display along with a single flashing tem
-
perature digit.
4.
Use the UP or DOWN buttons to change the number
of degrees desired for adjustment; 0° is the default
value and also means no correction will be applied.
5. Press the NEXT button to accept the setting.
NOTE:
All other features need to be completed in a
timely manner as the thermostat will time out
after 10 seconds.
KEYPAD LOCKOUT:
There is the option to lock the front panel buttons to pre-
vent unauthorized tampering of your thermostat settings.
To Lock the Keypad:
1.
Move TEMPERATURE switch to HEAT.
2.
Move SET switch to RUN.
3. Perform a single press of each button in the following
sequence:
•
NEXT, NEXT, NEXT, HOLD
A padlock will appear on the display screen.
To Unlock the Keypad:
1.
Move TEMPERATURE switch to HEAT.
2.
Move SET switch to RUN.
3. Perform a single press of each button in the following
sequence:
•
NEXT, NEXT, NEXT, HOLD
A padlock will no longer be present on the display screen.
14
Quadra-Fire • Pioneer III Owner’s Manual • 4182-900 • Rev D • 08/19
