background image

 2 

 

 

 

 

                       7061-197B 

 

 

 

       February 18, 2014

Explorer II Medium Wood Stove

TABLE OF CONTENTS

     Safety Alert Key:

• 

DANGER!

 

Indicates a hazardous situation which, if not avoided will result in death or serious injury.

• 

WARNING!

 Indicates a hazardous situation which, if not avoided could result in death or serious injury.

• 

CAUTION!

 

Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

• 

NOTICE:

 Indicates practices which may cause damage to the appliance or to property.

Quadra-Fire is a registered trademark of Hearth & Home Technologies.

Important Safety Information .............3

A.  Appliance Certification ......................................................3

B.  BTU & Efficiency Specifications........................................3

C.  Mobile Home Approved (USA ONLY) ............................... 3

D.  Glass Specifications .........................................................3

E. Non-Combustible Materials ...............................................3

F. Combustible Materials ........................................................3

Getting Started ....................................4

A. Design and Installation Considerations .............................4

B. Fire Safety .........................................................................4

C.  Negative Pressure ............................................................5

D.  Tools And Supplies Needed ..............................................5

E.  Inspect Appliance and Components .................................5

F. Install Checklist ..................................................................6

Dimensions and Clearances ..............7

A.  Appliance Dimensions ......................................................7

B. Clearances to Combustibles ..............................................8

C.  Locating Your Stove & Chimney .......................................9

D.  Chimney Termination Requirements ................................9

E.  2-10-3 Rule  ......................................................................10

Chimney Systems .............................11

A.  Venting Components  .......................................................11

B.  Chimney Systems .............................................................11

C. Installing Chimney Components ........................................13

Appliance Set-Up ..............................14

A.  Hearth Protection Requirements ......................................14

B. Outside Air Kit Installation  .................................................15

C.  Blower (Optional) ..............................................................16

D.  Reversible Flue Collar and Horizontal Flue Heat Shield ..17

Mobile Home Installation ..................18

Accessory List ..................................19

Summary of Contents for Explorer II Medium EXPLRMED-MBK





















Reviews: