background image

COLUMBIA BAY

DIRECT VENT GAS APPLIANCE

Owner’s Manual

Installation and Operation

Model: 

COLBAY-FS-B

O-T L

Tested and 

Listed by

Portland

Oregon USA

OMNI-Test Laboratories, Inc.

C

US

DO NOT DISCARD THIS MANUAL

CAUTION

•  Important operating and 

maintenance instructions 
included.

•  Leave this manual with 

party responsible for use 
and operation.

•  Read, understand and 

follow these instructions 
for safe installation and 
operation.

•  Do not store or use gasoline or other fl am-

mable vapors and liquids in the vicinity of this 
or any other appliance.

•  What to do if you smell gas   

-  D o   n o t   t r y   t o   l i g h t   a n y   a p p l i a n c e . 

                                                                       

Do not touch any electrical switch. Do not 
use any phone in your building.

-  Immediately call your gas supplier from a 

neighbor’s phone. Follow the gas supplier’s 
instructions.

-  If you cannot reach your gas supplier, call 

the fi re department.

•  Installation and service must be performed 

by a qualifi ed installer, service agency, or the 
gas supplier.

     WARNING:  If the information in these 
instructions is not followed exactly, a 

fi

 re 

or explosion may result causing property 
damage, personal injury, or death.

 

This appliance may be installed as an OEM installation in manufactured 
home (USA only) or mobile home and must be installed in accordance 
with the manufacturer's instructions and the manufactured home con-
struction and safety standard, Title 24 CFR, Part 3280 or Standard for 
Installation in Mobile Homes, CAN/CSA Z240MH.
This appliance is only for use with the type(s) of gas indicated on 
the rating plate.

Installation and service of this appliance should be 
performed by qualifi ed personnel. Hearth & Home 
Technologies suggests NFI certifi ed or factory-trained 
professionals, or technicians supervised by an NFI 
certifi ed professional.

DO NO

T

DISCARD

In the Commonwealth of Massachusetts:
•  installation must be performed by a licensed plumber or gas 

fi tter.

See Table of Contents for additional Commonwealth of Mas-
sachusetts requirements.

Page  1

10/08

Quadra-Fire  •  Columbia Bay  •  250-5195 Rev. K

WARNING

HOT SURFACES

Glass and other surfaces are hot during 
operation AND cool down.

Hot glass will cause burns.

•  Do not touch glass until it is cooled
•  NEVER allow children to touch glass
• Keep children away

•  CAREFULLY SUPERVISE children in same room as 

fi replace.

•  Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other 

fl

 ammable 

materials.

•  Keep clothing, furniture, draperies and other fl ammable 

materials away.

Summary of Contents for Direct Vent Gas Appliance COLBAY-FS-B


















































Reviews: