Quadra-Fire CB1200 Service Manual Download Page 11 | Manualshive

Page: 11 / 30

background image

CB1200-I PELLET STOVE SERVICE MANUAL

CB1200-I PELLET STOVE SERVICE MANUAL

EXHAUST BLOWER TESTING

7-31-2002 PAGE 11 250-7700

USING THE TEST BOX:

USING THE COMPONENT TEST CORD:

TEST BOX (AS IT IS INSTALLED IN THE STOVE)

1) UNPLUG THE STOVE, REMOVE THE CONTROL BOX, INSTALL THE TEST BOX & PLUG IN THE STOVE

2) TURN ON THE THERMOSTAT (THE THERMOSTAT INDICATOR LIGHT SHOULD COME ON)

3) TURN THE EXHAUST BLOWER SWITCH ON.

A. IF THE BLOWER COMES ON: REPLACE THE CONTROL BOX

B. IF THE BLOWER DOESN’T COME ON: CHECK THE WIRE HARNESS OR REPLACE THE BLOWER

1) UNPLUG THE BLOWER FROM THE WIRE HARNESS.

2) INSTALL THE EXHAUST BLOWER ADAPTER TO THE TEST CORD.

3) PLUG IN THE TEST CORD TO THE EXHAUST BLOWER AND TURN THE SWITCH ON.

TEST CORD w/ ADAPTER ATTACHED

EXHAUST BLOWER w/ TEST CORD

THERMOSTAT LIGHT

EXHAUST BLOWER SWITCH

«
...
9
10
11
12
13
...
»

Summary of Contents for CB1200































Reviews:

No comments

Related manuals for CB1200

Brand: Valor Pages: 18

Southern Series

Brand: Warmington Pages: 2

Brand: Quadra-Fire Pages: 36

Brand: Quadra-Fire Pages: 56

Brand: Endless Summer Pages: 24

Heatilator Icon Series

Brand: Heatilator Pages: 2

SAPLING EVAPORATOR

Brand: Vermont Castings Pages: 6

Brand: JAYLINE Pages: 10

Brand: HAMPTON BAY Pages: 9

Brooks 15PFP-BROO24-CHDRY

Brand: OVE Pages: 4

Brand: Panadero Pages: 44

Brand: Empire Comfort Systems Pages: 28

Brand: kozy heat Pages: 51

Brand: Comfort Glow Pages: 16

Brand: Lamborghini Caloreclima Pages: 116

Brand: Warmlite Pages: 12

Brand: FireplaceXtrordinair Pages: 10

Brand: Heat&Glo Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands