Quadra-Fire CASTILEI-CSB Installation Manual Download

Page: 1 / 32

7022-514C

July 7, 2015

CASTILE PELLET INSERT STOVE

Model(s):

CASTILEI-MBK

CASTILEI-PMH

CASTILEI-CSB

CASTILEI-CWL

Installation Manual

Installation & Appliance Set-Up

INSTALLER: Leave this manual with party responsible for use and operation.
OWNER: Retain this manual for future reference.

NOTICE: DO NOT DISCARD THIS MANUAL

O-T L

Tested and

Listed by

Portland

Oregon USA

OMNI-Test Laboratories, Inc.

HOT

SURFACES!

Glass and other surfaces are hot

during operation AND cool down.

Hot glass will cause burns.

•

Do not touch glass until it is cooled

•

NEVER allow children to touch glass

•

Keep children away

•

CAREFULLY SUPERVISE children in same room as
fi replace.

•

Alert children and adults to hazards of high temperatures

•

High temperatures may ignite clothing or other
fl ammable materials.

•

Keep clothing, furniture, draperies and other fl ammable
materials away.

WARNING

If the information in these instruc-
tions is not followed exactly, a
fi re could result causing property
damage, personal injury, or death.

• Do not store or use gasoline or other fl am-

mable vapors and liquids in the vicinity of
this or any other appliance.

• Do not overfi re - If heater or chimney con-

nector glows, you are overfi ring. Overfi ring
will void your warranty.

• Comply with all minimum clearances to

combustibles as specifi ed. Failure to
comply may cause house fi re.

WARNING

CAUTION

Tested and approved for wood pellets and corn pellets.
Burning of any other type of fuel voids your warranty.

NOTE

To obtain a French translation of this manual, please contact
your dealer or visit www.quadrafi re.com

Pour obtenir une traduction française de ce manuel, s’il vous
plaît contacter votre revendeur ou visitez www.quadrafi re.com

CAUTION

Check building codes prior to installation.
• Installation MUST comply with local, regional, state and na-

tional codes and regulations.

• Consult local building, fi re offi cials or authorities having juris-

diction about restrictions, installation inspection, and permits.

Summary of Contents for CASTILEI-CSB

































Search results

Summary of Contents for CASTILEI-CSB

Reviews:

Related manuals for CASTILEI-CSB

Brands by name

Popular brands

Quadra-Fire CASTILEI-CSB, Installation Manual

Search results

Summary of Contents for CASTILEI-CSB

Reviews:

Related manuals for CASTILEI-CSB

Brands by name

Popular brands