background image

PLEASE READ ALL OF THE OWNERS MANUAL AND SAFETY NOTES

IMPORTANT SAFETY NOTES:

1.

When installing your stove, particular attention should be paid to fire protection.  If this unit is not properly installed, a
house fire may result.  For your safety, follow the installation instructions and contact local building or fire officials
about restrictions and installation inspection requirements in your area.

2.

Never use gasoline or similar liquids to start a fire in this unit.  Keep all such liquids well away from stove.

3.

During operation, if any part of the stove starts to glow, the stove is in an overfired condition.  Close the air controls
completely until the glowing has stopped.  OVERFIRING VOIDS WARRANTY.

4.

Cool ashes should be disposed of carefully, using a metal container.

5.

Do not burn wet or green wood.  Store wood in dry location.

6.

Do not burn garbage, treated wood, or wood with salt (driftwood, etc.).  Burning materials other than wood (including
charcoal) under adverse conditions may generate carbon monoxide in the home, resulting in illness or possible death.

7.

Do not permit creosote or soot to accumulate excessively in the chimney or inside the firebox.

8.

Check your chimney system thoroughly when installing into an existing metal or masonry chimney.  Seek professional
advice if in doubt about its condition.

9.

Do not connect this unit to a chimney flue already serving another appliance.

10. Comply with all minimum clearances to combustibles as shown in this manual for this appliance.
11. Build fire on brick firebox floor.  Do not use grates, andirons or other method to support fuel.
12. HOT WHILE IN OPERATION.  Keep children, pets, clothing and furniture away.  Contact can cause skin burns.
13. Do not connect to any air distribution duct or system.
14. RISK OF FIRE!  Do not operate with stove door or ash removal system door open.
15.   For further information refer to NFPA 211 (U.S.) or CAN/CSA-B365 (Canada).
16. WARNING:  WHEN ASSEMBLING A UNIBODY APPLIANCE, USE ONLY GENUINE ALADDIN HEARTH

PRODUCTS MANUFACTURED COMPONENTS.  USE OF ANY OTHER COMPONENTS WILL VOID YOUR
WARRANTY, AND COULD PRESENT A SERIOUS SAFETY HAZARD.

17. WARNING:  DO NOT OPERATE YOUR QUADRA-FIRE STOVE BEFORE FULLY ASSEMBLING ALL

COMPONENTS.  BURNING YOUR STOVE WITHOUT A PEDESTAL OR LEG KIT ATTACHED WILL VOID
YOUR WARRANTY, AND COULD PRESENT A SERIOUS SAFETY HAZARD.

(Revised 01/1999)

INSTALLATION, OPERATION, AND MAINTENANCE INSTRUCTIONS

QUADRA-FIRE 3100 SERIES

www.aladdinhearth.com

[email protected]

401 N. WYNNE
COLVILLE, WA  99114

North 

America’s 

Best

SAVE THESE INSTRUCTIONS

CONGRATULATIONS—You are now the proud owner of one of the finest stoves in the world for your home —the
QUADRA-FIRE.  Now, before installing your stove and building your first fire—record the serial number on the
warranty card.  Serial number is located on the safety label on the rear of the stove.

Part #250-3500 #832-3050

Summary of Contents for 3100 Series

































Reviews: