QTech XLINE Series Installation And Programming Manual Download Page 15

QIR100H | © 2022 Inim Electronics S.r.l.

15

4.4  Limited warranty

4.4  Limited warranty

Inim Electronics S.r.l. shall not be liable to the purchaser or any other person for damage arising from impro-

per storage, handling or use of this product.
Installation of this Product must be carried out by qualified persons appointed by Inim Electronics. Instal-

lation of this Product must be carried out in accordance with Our instructions in the product manual.

4.5  Documents for the users

Declarations of Performance, Declarations of Conformity and Certificates concerning to Inim Electronics 

S.r.l. products may be downloaded free of charge from the web address www.inim.biz, getting access to 

Extended Access and then selecting "Certifications" or requested to the e-mail address [email protected] or 

requested by ordinary mail to the address shown in this document.
Manuals may be downloaded free of charge from the web address www.inim.biz, getting access to the reser-

ved area, after the login, and then to the section of each product.

4.6  Disposal of the product

Informative notice regarding the disposal of electrical and electronic equipment (applicable 

in countries with differentiated waste collection systems)

The crossed-out bin symbol on the equipment or on its packaging indicates that the product must be 

disposed of correctly at the end of its working life and should never be disposed of together with gene-

ral household waste. The user, therefore, must take the equipment that has reached the end of its working 

life to the appropriate civic amenities site designated to the differentiated collection of electrical and elec-

tronic waste. As an alternative to the autonomous-management of electrical and electronic waste, you can 

hand over the equipment you wish to dispose of to a dealer when purchasing new equipment of the same 

type. You are also entitled to convey for disposal small electronic-waste products with dimensions of less 

than 25cm to the premises of electronic retail outlets with sales areas of at least 400m2, free of charge and 

without any obligation to buy. Appropriate differentiated waste collection for the subsequent recycling of the 

discarded equipment, its treatment and its environmentally compatible disposal helps to avoid possible 

negative effects on the environment and on health and favours the re-use and/or recycling of the materials it 

is made of.

Summary of Contents for XLINE Series

















Reviews: