Q'STRAINT INQLINE SECUREMENT Use And Care Manual Download Page 18 | Manualshive

Page: 18 / 28

background image

18

5.

Then press the Unlock Button to unlock front

Retractors and move the wheelchair back a few inches

(MM).

If the front INQLINE SECUREMENT™ Retractors do NOT

release, make sure someone is behind the wheelchair

to hold it in place before cutting the front webbings

at an angle with the Q’Straint® Emergency Cutter

(NN).

6.

Press Levers and detach rear J-Hooks (PP).

7.

Remove rear QRT Retractors from floor by lifting

the Slide ‘N Click® and sliding out the retractors (QQ).

If the front INQLINE SECUREMENT™ Webbing was cut

proceed to the next step (RR). If Webbing was not cut

proceed to step 9.

MM

NN

PP

QQ

RR

Someone Behind Wheelchair to Hold it in Place

Webbing Was Cut

EMERGENCY RELEASE

Press

«
...
16
17
18
19
20
...
»

Summary of Contents for INQLINE SECUREMENT





























Reviews:

No comments

Related manuals for INQLINE SECUREMENT

Brand: Abilize Pages: 22

Brand: R82 Pages: 9

Brand: E&J Pages: 32

Brand: Gate Pages: 20

Brand: Sertain Pages: 27

Brand: Quickie Pages: 36

Brand: Sunrise Medical Pages: 18

Brand: SOMA Pages: 32

Brand: PDG Mobility Pages: 14

Brand: B+B Pages: 85

Brand: B+B Pages: 87

Brand: Küschall Pages: 40

Brand: PDS hygiene Pages: 2

ErGo Selpro 1000

Brand: RehabCare Pages: 16

Brand: Dietz Pages: 60

Stealth Positioning Pelvic Belts

Brand: Stealth Products Pages: 4

Configura Advance Chair

Brand: Accora Pages: 24

Brand: Ferno Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands