background image

24

Preliminary Specification

IN

OUT

THRU

Dynamic Range (AES-17, -60dB Method, all sensitivities)

unweighted

>110dB

>112dB

>108dB

A weighted

>113dB

>115dB

>111dB

Distortion (20Hz-20 KHz, all sensitivities)

Gain= 0 - 30dB

<0.008% THD+N

<0.009% THD+N

<0.009% THD+N

Gain >30dB

<0.05% THD+N

<0.009% THD+N

<0.05% THD+N

Crosstalk (20Hz - 20KHz)

inter-channel (max)

>75dB

inter-channel (typ)

>90dB

intra-channel (max)

>85dB

intra-channel (typ)

>100dB

Frequency Response

20Hz - 20KHz (max)

± 0.5dB

20Hz - 20KHz (typ)

± 0.2dB

Program Inputs

8

Connector Type

3-pin "Phoenix Style" (a.k.a. "Euro Style") detachable terminal blocks

Type

Electrically balanced

Grounding

All shield terminals connected to chassis

Pinout

1:+  2:-  3:CHASSIS GND

Input Impedance (nom.)

Balanced: 6.81k ohms

Unbalanced: 13.6k ohms

Common-Mode Rejection

20Hz - 20KHz (min.): >54dB,20Hz - 20KHz (typ.): >60dB

E.I.N.(max.)

150 ohm, 30dB: -124.5dBu150 ohm, 60dB: -125.0 dBu

Input Sensitivities (variable)

Vrms: 0.9 mV to 15.46 V

dBu: -62.2 to +26dBu

dBV: -64.4 to +23.7 dBV

Phantom Power (per IEC 1938 (1996))

+48V (software-selectable)

Program Outputs

8

Connector Type

3-pin "Phoenix Style" (a.k.a. "Euro Style") detachable terminal blocks

Type

Electrically balanced

Grounding

All shield terminals connected to chassis

Pinout

1:+  2:-  3:CHASSIS GND

Maximum Output Level

9V (rms ), +21.2 dBu, +19 dBV

Audio Converters

24 bit, 48KHz, in and out

Mute

infinite attenuation

Delay

Standard CobraNet Latency

Low Latency

RAVE to Network

Analog input through full DSP chain to CobraNet output

7.104 milliseconds

4.438 milliseconds

Network to RAVE

CobraNet input through full DSP chain to analog output

6.313 milliseconds

3.646 milliseconds

RAVE to RAVE

Analog input through full DSP chain, over CobraNet network,
through full DSP chain, to analog outputs

8.083 milliseconds

5.417 milliseconds

RAVE in stand-alone mode

Analog input through full DSP chain to analog outputs

2.354 milliseconds (Default Group Delay)

Specifications are subject to change without notice.

Summary of Contents for RAVE 522ua





























Reviews: