background image

15

Specifications

Hardware

Dimensions (H/W/D)
Line voltage requirements
Accessories included

10.37” x 8.3” x 1.5” (263.4 mm x 210.8 mm x 38.1 mm)
IEEE 802.3af power or +24 VDC/500 mA
Hardware User Manual, Accessory ship kit, Warranty card

Audio Channel Capacity

Line Inputs
Line Outputs


1

Front Panel Controls

Paging keypad
Microphone

Capacitive touch keypad, PTT momentary button
PTT momentary switch (hand-held models only)

Front Panel Indicators

Talk, Ready, Busy
Keypad button activity
LCD

Bi-color LEDs (red/green)
Green LEDs
240x64 monochrome graphics display

Rear Panel Connectors

Hand-held microphone
Q-LAN Network LAN A and LAN-B
DC power +24 VDC inlet
Line Input
Line Output
GPIO

RJ45
RJ45 1000 Mbps only
2-pin Euro receptacle
3-pin Euro receptacle
3-pin Euro receptacle
6-pin Euro receptacle

Line Input

Dynamic range 

Unweighted
A-weighted

>115 dB
>118 dB

Distortion (20 Hz  – 20 kHz, all sensitivities)

+4 dBu (maximum)
2 dB below clip (maximum)

<0.009% THD+N
<0.009% THD+N

Crosstalk (20 Hz – 20 kHz)

Inter-channel (maximum)
Inter-channel (typical)
Intra-channel (maximum)
Intra-channel (typical)

>75 dB
>90 dB
>85 dB
>100 dB

Frequency response

20 Hz – 20 kHz (maximum)
20 Hz – 20 kHz (typical)

± 0.5 dB
± 0.2 dB

Input impedance

Balanced (nominal)
Unbalanced (nominal)

10k ohms
10k ohms

Common mode rejection:

20 Hz – 20 kHz (minimum)
20 Hz – 20 kHz (typical)

>54 dB
>60 dB

Input sensitivities:

Vrms
dBu
dBv

1.5, 3, 9, 18
5.7, 11.8, 21.3, 27.3
3.5, 9.5, 19.1, 25.1

Line Output

Dynamic range

Unweighted
A-weighted

>112 dB
>115 dB

Crosstalk (20 Hz – 20 kHz)

Inter-channel (maximum)
Inter-channel (typical)
Intra-channel (maximum)
Intra-channel (typical)

>75 dB
>90 dB
>85 dB
>100 dB

Mute

Infinite attenuation

Optional Accessories

PS-X Page Station Expander

Summary of Contents for Q-SYS PS-1600H


















Reviews: