background image

13

TD-000347-00-A

NOTE!:

 

When you connect the ribbon cable to the Core main board be sure that you connect it to the proper connector. The 

connectors on the Core main board are identified by the slot letters A through H.

9.  When replacing the Blank Card with an I/O Card, the new ribbon cable must also be 

attached to the Core main board. To do this, locate the main board audio connectors. Then 
locate the appropriate card position indicator (

Figure 15

) on the main board for the card 

being replaced (A through H). Attach the ribbon cable in the same manner as the I/O Card, 
ensuring that the cable connector tab is aligned with the main board connector key and that 
the cable is properly seated with the ejector tabs in their locked position. 

10. Replace the Core lid and secure the lid with the screws removed earlier. 

Qualified Ethernet Switches

Q-Sys uses layer 3 (DSCP) QoS. This type of QoS is deployed differently on different networks 
and therefore requires user intervention to set up properly. Because of this complexity, unmanaged switches are not acceptable for Q-Sys. For 
more details about network and switch setup, refer to the Help File in Q-Sys Designer. For more details about the following switches, refer to the 
manufacturers’ website. The following switches have been tested and qualify for use with a Q-Sys™ network.

NOTE!:

 

Refer to the Q-Sys Online help on the QSC website for the latest list of switches.  

(http://www.qscaudio.com/products/software/QSys/WebHelp/)

Linksys

®

 HP® ProCurve™

Cisco®

Alaxala 

1

SLM Series Smart Switches (EOL)

3500 Series

Catalyst 3560E Series

Small Business 300 Series

Alaxala AX2500S Series

SLM2005

3500yl-24G-PWR

3560E-24TD

SG-300-10

AX2530S-24T

SLM2008

3500yl-24G-PoE+ 

3560E-24PD

SG-300-10P

AX2530S-48T

SLM2024

3500yl-48G-PWR

3560E-48PD 

SG-300-10MP

AX2530S-24S4X

SLM2048

3500yl-48G-PoE+

3560E-48TD

SG-300-20

AX2530S-24T4X

SRW Series Managed Switches (EOL)

Other

3560E-48PD-F

SG-300-28

AX2530S-48T2X

SRW2008

5406zl (all modules)

3560E-12D

SG-300-28P

Alaxala AX3640S Series

SRW2008MP

5412zl (all modules)

3560E-12SD

SG-300-52

AX3640S-24T

SRW2008P

6200yl-24G-mGBIC

Catalyst 3750 Series

AX3640S-24TW

SRW2016

3750E-24TD

AX3640S-24T2XW

SRW2024

3750E-24PD

AX3640S-48TW

SRW2024P

3750E-48TD

AX3640S-48T2XW

SRW2048

3750E-48PD 

AX3640S-24SW

3750E-48PD-F

AX3640S-24S2XW

1  Alaxala switches are available only in Japan.

— Figure 15 — 

Summary of Contents for Q-SYS Core 250i



















Reviews: