4
TD-000515-01-D
Rear Panel Features
— Figure 2 —
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
123456789
SERIAL: 123456789
MODEL: DPM 300 / 300H
1.
HDMI IN / OUT
(DPM 100H and DPM 300H only) – Extracts audio
from incoming HDMI stream and passes stream directly to output
HDMI port. Includes Dolby Digital Plus™, and DTS-HD
®
decoder.
2.
NETWORK
(RJ45) – 10/100 Mbps Ethernet port for DPM Manager,
3rd party control, or SNMP management and remote access.
3.
AUTOMATION INPUTS
(RJ45) – contact closures (control presets,
mute etc.)
4.
RS 232
– Serial communications port for 3rd party control/automation
5.
CH 1-8 AES/EBU INPUTS
(RJ45) – AES3 pairs 1 through 4 (digital
audio channels 1 through 8)
6.
CH 15-16 AES/EBU INPUTS
(RJ45) – AES3 pair 8 (digital audio
channels 15 and 16, normally HI and VI)
7.
SPDIF INPUT
– SPDIF multi-channel digital input for non-sync/
alternative content. Includes Dolby Digital Plus™ (DPM 100H and
DPM 300H only) or Surround LtRt Matrix decoding.
8.
ANALOG INPUTS
(DB-25) – connect to D-Cinema server or film
processor with analog outputs
9.
LINE INPUTS (L R)
(3.5 mm TRS) – Stereo analog line-level inputs
10.
MIC / LINE INPUT
(XLR) – Mono analog input accepts microphone
or line-level signals (with phantom power)
11. Serial Number and Model
12.
OUTPUTS TO DataPort™ AMPLIFIERS
(HD-15) connectors – For
QSC DataPort amplifiers. There are 9 DataPorts on DPM 100/100H; 11
DataPorts on DPM 300/300H.) Use only QSC-supplied DataPort cables.
13.
H.I.
/
V.I.
– Hearing impaired and visually impaired special mix
outputs
14.
RELAY OUTPUTS
– mechanically de-coupled control outputs (curtain,
lighting control, and so on.)
15.
POWER
ON / OFF switch
16. IEC connector – AC mains power connector
DPM Manager Software
DPM Manager is used to configure and manage your DPM and to configure the network settings if required.
Your computer must meet the following minimum requirements:
1. Computer with Windows® 7, 8, or 10 OS (32 or 64 bit) or MAC OS 10.9.5 or higher
2. 4 GB of RAM or greater
3. Display resolution of at least 1024 x 768
Setup Overview
Initial configuration of the DPM is performed through QSC’s DPM Manager software, which must be installed on a Windows® or MAC PC or laptop
computer. Once the software is installed on the computer, the computer can then be connected to the DPM using a USB or Ethernet connection.
A system designer would typically begin high-level configuration by defining the basic system topology and distribution of audio within the
DPM Manager application. This involves selecting the audio sources for the DPM program inputs, auditorium sound format, amplification, and speaker
design. Presets can be created to accommodate multiple audio sources or distribution topologies (i.e.., to support different configurations for the main
theatre presentation and for alternative content/non-sync audio) and/or to support multiple auditorium mixes or multi-use applications.
Once the high-level configuration is complete, the rest of system can be connected to the DPM and/or powered up and completion of the DSP
configuration, assignment of levels, and other system tuning can commence.
