background image

                      

CAI-QSP-01

QSeal Plug Customer Assembly Instructions

 

Page 9 of 9 

 

FINAL ASSEMBLY 

Place the Insert end into the Body Assembly. The tabs on the Spacer should engage with the slots on 
the Body Assembly. Slide the Backshell into position and tighten by hand onto the Body Assembly 
making sure that the Spacer does not turn relative to the Body. Insert the Plug Assembly onto the 
Torque Fixture Stand PT-317. The fixture accommodates both the 2 and 4-channel plugs. 

For the QSeal with Grip, torque the Backshell using Dial Torque-Measuring Wrench PT-506 with 
Crow’s Foot Wrench PT-536 to the values in the above Torque Table. Make sure not to over torque the 
Backshell as this will cause damage.  

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

For the All-Metal Plug, tighten the Backshell using Dial Torque-Measuring Wrench PT-506 with Square 
Driver Strap Wrench PT-415 to the values in the Torque Table above. Finally, tighten the Back Nut 
using these same torque tools to the values in the Torque Table above. 

 

 

 

 

 

 

 

 

NOTE: After torqueing, ensure that the insert is clocked properly in the Body with respect to the main 
key. 

Summary of Contents for QSEAL PLUG












Reviews: