background image

Component

TVS-872XU

TVS-872XU-RP

TVS-1272XU-RP

Rail compatibility

RAIL-B02

Note

• Rail kits are not included with the NAS and must

be purchased separately. For details, contact an
authorized reseller or go to 

http://shop.qnap.com

.

• Information on rail kit installation can be found in

the installation guide included in the rail kit
package.

Power supply unit

• TVS-872XU: 350W, 100-240V

AC, 50/60Hz

• TVS-872XU-RP: 2 x 300W,

100-240V AC, 50/60Hz

2 x 300W, 100-240V AC, 50/60Hz

System battery

CR2032 lithium battery (3V, 225 mAh)

Warning

To avoid potential battery explosion, causing injury or
damage to components, ensure that you replace the
existing battery with a battery of the same type.

Important

Dispose of used batteries according to local
regulations or the instructions of the battery
manufacturer.

Sound level

• TVS-872XU: 54.2 db(A)

• TVS-872XU-RP: 52.1 db(A)

52.7 db(A)

Note

The sound level was tested at a bystander position,
which is within one meter of the NAS. The test NAS
operated at low speed with the maximum number of
drives installed.

Fans

System: 2 x 60 mm, 12V DC

Warning

To avoid potential injury or damage to components, do
not touch the fans while the NAS is connected to a
power source.

Operating temperature

0˚C to 40˚C (32˚F to 104˚F)

Relative humidity

• Non-condensing relative humidity: 5% to 95%

• Wet-bulb temperature: 27˚C (80.6˚F)

Tip

Model specifications are subject to change without prior notice. To see the latest
specifications, go to 

https://www.qnap.com

.

TVS-x72XU User Guide

Product Overview   

6

Summary of Contents for TVS-1272XU-RP






















































Reviews: