manualshive.com logo in svg

Qiagen Hybrid Capture Rotary Shaker 1, User Manual, Page: 6 / 44

Share
Download
Qiagen Hybrid Capture Rotary Shaker 1 User Manual Download Page 6

6 

Hybrid Capture System Rotary Shaker 1 User Manual   09/2018 

2

 

Safety Information 

This manual contains information about warnings and cautions that must be followed by the 
user to ensure safe operation of the HCS Rotary Shaker 1 and to maintain the instrument in a 
safe condition. 

WARNING

 

The term 

WARNING

 is used to inform you about situations that could result 

in personal injury to you or other persons. 
Details about these circumstances are provided to avoid personal injury to 
you or other persons. 

CAUTION

 

The term 

CAUTION

 is used to inform you about situations that could result in 

damage to the instrument or other equipment. 
Details about these circumstances are provided to avoid damage to the 
instrument or other equipment. 

Before using the instrument, it is essential to read this manual carefully and to pay particular 
attention to any details it contains concerning hazards that may arise from the use of the 
instrument. 

The details given in this manual are intended to supplement, not supersede, the normal safety 
requirements prevailing in the user’s country. 

Summary of Contents for Hybrid Capture Rotary Shaker 1













































Reviews:

No comments