Qel Q4 Controller II Installation, Operation And Maintenance Manual Download | Manualshive

Page: 7 / 26

background image

Q4 CONTROLLER II Operation and Maintenance Manual

Q4 Controller II Operation Manual

- 6 -

Dec 02, 2021

85350-101-000 Rev A

4. Installation

4.1 Unpacking the equipment

The Q4 Controller is shipped with the following:



The Q4 Controller in a NEMA 4X enclosure



M-View USB Flash Drive



User Operation Manual



Installation Drawing



USB Cable A to B M/M



Enclosure mounting feet kit

4.2 Type and Location

The Q4 Controller is designed and certified for installation in a fixed location where is not subject
to shock and vibration. Please observe the temperature and humidity specifications above for
ambient conditions. Observe the possibility of leaks or possible water damage from cleaning done
in the area.

The mounting height and location should provide easy access to the wiring terminals and front-
panel. Backlighting is provided for the display in case of low lighting conditions.

It is recommended that controllers be installed 5 feet (1.5m) above the floor, at approximate eye
level. Securely mount the controller using the appropriate screws.

«
...
5
6
7
8
9
...
»

Summary of Contents for Q4 Controller II



























Reviews:

No comments

Related manuals for Q4 Controller II

Brand: National Instruments Pages: 29

Brand: Jetter Pages: 24

Brand: Challenger Lifts Pages: 20

Liberty Vertical Picket

Brand: National ramp Pages: 9

Pulsafeeder MPC Vector

Brand: Idex Pages: 114

Brand: Measurement Computing Pages: 32

Brand: Fancom Pages: 23

Brand: Beninca Pages: 7

Brand: Acuity Controls Pages: 5

Brand: Risco Pages: 232

CompleteStat-Series CS9B-THO

Brand: Bard Pages: 2

Gator Grip Drum EGG-1

Brand: Wesco Pages: 2

Brand: SMC Networks Pages: 15

Brand: Anritsu Pages: 54

Brand: Governors America Pages: 6

Brand: SKF Pages: 11

Brand: Quectel Pages: 97

Brand: Danfoss Pages: 162

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands