background image

Information requirements regarding the eco-design

Description

Symbol

Value

Unit

Maximum fan flow rate

F

64.16

m

3

/min

Fan power input

P

43.50

W

Service value

SV

1.47

(m

3

/min)/W

Standby power consumption

PSB

0.0

W

Seasonal electricity consumption

Q

13.92

kWh/a

Fan sound power level

LWA

43.50

dB(A)

Maximum air velocity

c

1.42

m/seg

Regulation Nº 206/2012

IEC 60879:1986

EN 50564:2011

Measurement standard for service

EN 60704-2-7:1998

EN 60704-1:2010

[Shall not appear all of these ones, but the same as the ones which are

detailed in the ERP test report]

PREFACE

Y

our ceiling fan may sometimes have wobble problem when operate due to irregularity in blades or the blade holder. Also, improper assembly in the mounting system

may cause some additional problem also bearing crooked. The following procedure to remedy such problem is strongly recommended by us from our past experience in
handling the wobble  problem.

D

ynamic blade balancing kit for ceiling  fans

1.

M

ake sure that all blade are firmly screwed into the blade holder

2.

M

ake sure that all blades are firmly secured the flywheel and check pitch of blade holders all must be the same

3.

B

y  looking up the  fan from below, check and be certain that none of the  blade holders are bent  so  that  none of the  blade is  out of position. A correction can be

made by very gently bending the blade holder back into position

4.

B

y the simple use of a household yardstick blade tracking can be checked, out the yardstick up against the ceiling vertically and even with the outside leading edge

of a blade. Note the distance of the edges of the blade to t he ceiling; carefully turn the blade slowly by hand to check the remaining blades. If blade is not in
alignment, the blade holder may be gently bent up or down to be in line with the other blades

I

f by following all the steps and the wobble problem is not solved, a dynamic balancing need to be done by the use of the balancing kit. Follow

the procedure listed  below:

T

urn the fan on and adjust the speed control (usually high speed) setting to the speed, which creates to greatest wobble.

T

urn the fan off; select on blade place the balance clip on it. Halfway between the blade holder and the blade up on the rear edge of the blade.

T

urn the fan on, watch to see of the wobble is improved or worse. Then, turn the fan off again and move the clip to another blade and test again. Repeat this process

with all blades and then note that blade which is the most  improved.

M

ove the clip back to the blade, which showed the most improvement. Move the clip inward and outward on this blade and operate t he fan to find the position

where the clip gives the most improvement

N

ext remove the clip and install a balancing weight to the top of the blade along the centerline near the point where the clip was positioned.

C

aution: stay clear of the blades if the clip for any  reason is not secured, injury could result

12) Others

H

ave your product repaired by a qualified person

T

his  electric product is  in accordance with the  relevant  safety  requirements.  Repairs  should only be carried out by qualified persons using original spare parts; otherwise

this  may result  in considerable danger to the user.  This  appliance can be used  by children aged from 8 years  and above if they have been given supervision or  instruction
concerning use of the appliance in a safe way and if they understand the hazards involved. Cleaning and user maintenance shall not be made by children unless they are older 
than 8 and supervised. Keep the appliance and its cord out of reach of children aged less than 8 years.

P

lease contact the store which you bought the product for after sale services if question

T

his appliance can be used by children aged from 8 years and above if they have been given supervision or instruction concerning use of 

the appliance in a safe way and if they understand the hazards involved. Cleaning and user maintenance shall not be made by children  
unless they are older than 8 and supervised. Keep the appliance and its cord out of reach of children aged less than 8  years.

A

ppliances can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they  have been 

given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.

Children shall not play with the  appliance.

P

lease contact the store which you bought the product for after sale services if question

P.8

Summary of Contents for Xiro










Reviews: