background image

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8. How to use

   

- One pull chain switch is for light control, another one for speed control 
- The speed can be selected by pressing the speed chain 
HI-1    pull, MED 

–2    pull, LOW—3    pull, OFF----4    pull 

 
- Light on off can be controlled by pressing the light chain 
ON-1      pull, OFF

–2      pull 

 

Direction switch on the fan ‘s switch box(SUMMER and WINTER switch) 

- Down for summer make the air movement directly from ceiling 
- Up for winter, to circulate the warm air generated by heater to floor 
 
 
 
 

9. Remote Control    (remote control adaptable, but this model does not included)

 

This ceiling fan can be installed with remote control, but make sure you know how to install the device in safe way or

 

consult licensed electrician 
Warranty may be affected if you install the improper remote control or install it in improper way 
 

10.Disconnect from mains before maintenance or cleaning. 

Do not use a wet sponge to clean the appliance. 
1. Before conducting any cleaning or maintenance work, disconnect the lamp from the electrical supply and wait until it 
cools down 
2. No abrasive products, solvents, detergent or any other liquid may be used to clean the fan or lamp 
3. Be sure the power is off when you clean the fan 
4. Don’t clean the motor, switch house and other electric parts of the fan with water in order to avoid short circuit 

 

 

 

st                                  nd                                  rd                                  th 

st                                  nd                                 

 

P.9 

 

 

Summary of Contents for 89522













Reviews: