Q-SYS PL-DC Series User Manual Download Page 4

4

EXPLANATION OF SYMBOLS

The term “

WARNING!

” indicates instructions regarding personal safety. If the instructions are not followed, the result may be bodily 

injury or death.

The term “

CAUTION!

” indicates instructions regarding possible damage to physical equipment. If these instructions are not followed, it 

may result in damage to the equipment that may not be covered under the warranty.

The term “

IMPORTANT!

” indicates instructions or information that are vital to the successful completion of the procedure.

The term "

NOTE

" is used to indicate additional useful information.

The lightning flash with arrowhead symbol in a triangle alerts the user to the presence of uninsulated dangerous voltage 
within the product’s enclosure that may constitute a risk of electric shock to humans. 

The exclamation point within a triangle alerts the user to the presence of important safety, operating, and maintenance 
instructions in this manual.

IMPORTANT SAFETY INSTRUCTIONS

 

WARNING!: 

While it is possible for one person to lift a loudspeaker, it is important to use proper lifting techniques. 

Suggested reading: OSHA Technical Manual (OTM) > Back Disorders and Injuries: https://www.osha.gov/otm/ 

1.  Read, follow, and keep these instructions.

2.  Heed all warnings.

3.  Clean only with a dry cloth.

4.  Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that 

produce heat.

5.  Only use attachments/accessories specified by the manufacturer.

6.  Refer all servicing to qualified service personnel. 

7.  Adhere to all applicable, local codes.

8.  Consult a licensed, professional engineer when any doubt or questions arise regarding a physical equipment installation.

9.  Suspension of this product should be done by qualified persons following safe rigging practices. Other limitations may apply. 

10.  Use only the recommended system components and suspension hardware intended for use with this product as directed by this 

manual.

 

WARNING!: 

Read and follow the installation instructions carefully. If these products are not suspended properly, they 

could fall, causing personal injury or death and damage to the equipment. Refer to the user manual for rules on suspension.

Summary of Contents for PL-DC Series



























Reviews: