Q-See QC818 User Manual Download Page 38

75

74

PICTURE 5-12

RUNNING PTZ FUNCTIONS

Clicking on the 

Page Switch

 button in the 

PTZ Control Panel

 (

Picture 5-6

) will switch to a 

new window (

Picture 5-12

) which allows you to activate the functions created above as well 

as the Auto Pan and Flip functions.  

Enter the number of the function you wish to 
activate and select the function button to run 
that function.

In addition, there are other functions that can 
be engaged in this window.

AutoPan

 - This will cause the camera to 

automatically rotate.

Flip

 - Most PTZ cameras have a mechanical 

stop which will prevent the camera 
from rotating a full 360°. If the camera 
is tracking someone or some thing 
and it reaches this stop, pressing Flip 
will bring the camera around the other 
direction to continue tracking.  Some 
PTZ cameras have “E-flip” which will 
do this automatically.

Page Switch

 - returns you to the 

PTZ 

Control Panel

 (

Picture 5-6

)

Reset

 - This ends the currently running 

function.

NO C

1

NO C

2

1 2 3 4

5 6 7 8

A B

CNTRL

12V

ALARM IN

This NVR features connections for external alarms – both input and output. When an event is 
detected the system can notify local users or send notification to a monitoring service. At the 
same time, the system can accept signals from motion detectors, smoke detectors or other 
alarms and begin recording based on that input and your settings.
You will need to have the manual for your alarm(s) handy to ensure the proper settings within 
the NVR. 

ALARMS

CHAPTER 6

6.1 ALARM INPUT

When attaching alarms, the following criteria 
must be met:
1.   The alarm input must be grounded.
2.  A grounding signal is required for the 

alarm input

3.  When connecting the NVR to another 

device - including another NVR - through 
the alarm input, a relay should be used to 
separate them.

Parameter

Grounding Alarm  

 

Ground line

Alarm Input

1, 2, …, 8 becomes valid in low voltage.

1-NO C
2-NO C

Two NO activation outputs.

CTRL 12V 

Controls the power output
You need to close the device power to 
cancel the alarm. 

PICTURE 6-1

Summary of Contents for QC818















































Reviews: