manualshive.com logo in svg

Q-Pumps QTS 203, Operation And Maintenance Manual, Page: 41 / 44

Share
Download
Q-Pumps QTS 203 Operation And Maintenance Manual Download Page 41

41

Operation and Maintenance Manual 

QTS Series Twin Screw Positive Displacement Pump

QTS-M04

After CIP cleaning an additional sterilization in place process (SIP) may be required when highly 

sensitive products are handled, inactivating any micro-organisms which might be still present in 

the pump.  The sterilization can be carried out by means of chemicals, hot water or steam.  In the 

dairy industry the sterilization temperature is approximately 145 °C (293 °F). Contact Q-Pumps in 

case of temperatures above 100 ºC (212 ºF).

 

Because of QTS pumps are capable to supply the CIP fluid running at high speed please provide 

system information for selecting the right values of rpm for CIP supply.

Normally when ordered, the QTS Pumps are selected for both, the application and for the CIP supply.

Rpm speed table for each pump model, for turbulent flow to achieve the CIP process in different pipes:

Pipe Diameter

1.5

2.0

2.5

3.0

4.0

6.0

QTS102 - 1.5 m/s

1146

2100

3372

QTS102 - 3.0 m/s

2291

QTS103 - 1.5 m/s

1707

3133

QTS103 - 3.0 m/s

3414

QTS202 - 1.5 m/s

799

1281

1418

QTS202 - 3.0 m/s

1598

2562

QTS203 - 1.5 m/s

1188

1906

2149

QTS203 - 3.0 m/s

2375

QTS302 - 1.5 m/s

532

780

1418

QTS302 - 3.0 m/s

1064

1562

QTS303 - 1.5 m/s

807

1183

2149

QTS303 - 3.0 m/s

1612

2370

For more information please contact Q-Pumps.

A

N

N

E

X

 A

Summary of Contents for QTS 203













































Reviews:

No comments