Q CELLS Q.PEAK DUO L-G8 Series, Installation And Operation Manual

Page: 5 / 12

8 9 INSTALLATION AND OPERATION MANUAL SOLAR MODULES Q.PEAK DUO L-G8.X – Q CELLS INSTALLATION AND OPERATION MANUAL SOLAR MODULES Q.PEAK DUO L-G8.X – Q CELLS
Specifications
MODULE TYPE
MOUNTING
OPTION POSITION OF
CLAMPS* [MM] TEST LOAD
PUSH/PULL** [PA] DESIGN LOAD
PUSH/PULL** [PA] SAFETY
FACTOR
Q.PEAK DUO L-G8.X
CL1 250 - 500
5400 / 2400 3600 / 1600
1.5
FB1 386
CL3 250 - 500 3600 / 2400 2400 / 1600
IP1 - 3600 / 2400 2400 / 1600
CL1 0 - 250 2400 / 2400 1600 /1600
CL5
short side: 100 - 250
long side: 250 - 500
3600 / 2400 2400 / 1600
Q.PEAK DUO L-G8.1
Q.PEAK DUO L-G8.2
TB1
840 at Tracker holes 2400 / 2400 1600 /1600
TC1
830 - 890 2400 / 2400 1600 /1600
Ä The below mounting options are only possible under certain conditions.
MODULE TYPE
MOUNTING
OPTION POSITION OF
CLAMPS* [MM]
TEST LOAD
PUSH/PULL***
[PA] DESIGN LOAD
PUSH/PULL***
[PA]
SAFETY
FACTOR
Q.PEAK DUO L-G8.X
CL2a (with rails) 0 - 300**** 2400 / 1600 1600 / 1067
1.5 CL2b (without rails) 0 - 300 1800 / 1600 1200 / 1067
IP2 - 1800 / 1600 1200 / 1067
*
**
***
**** Distance between outer edge of module and middle of the clamp (see table „2.3 Mounting Options“ on page 7).
Loads according to IEC 61215-2:2016 and UL 1703.
Test procedure according to IEC 61215-2:2016 and UL 1703. Mounting options do not fulfill the requirements of the standards.
Rails must not be under the junction box.
ATTENTION
Ä The loads in the table are related to the mechanical stability of the solar modules. The mechanical stability of the mounting
system including clamps has to be evaluated by the system supplier. The Q CELLS listed test load values were determinded
with the following clamp parameters: clamp width = 40 mm and clamp depth = 10 mm. The system installer is responsible for
the determination of location-specific load requirements.
Ä Ensure, that the subconstruction does not touch the junction box (even under load). Ensure that the clamps or insertion profiles
etc. do not touch the glass (even under load).
Ä Ensure, that the connection cables of the junction box do not run between laminate and mounting rails.
Ä Ensure, minimum support depth of 20 mm on the back side of the module for IP1, IP2, CL2b and CL5. Ensure minimum support
depth of 10 mm on the front side of the module for IP1 and IP2.
Ä CL1, CL2a and CL3 with rails: Ensure that module frame is fixed directly on the rail of the substructure (no spacer allowed
between the module and substructure).
Ä
Module bend under loads. Therefore, sharp objects (e.g. screws) must not be mounted near the module backside.
Ä Use M8 corrosion-proof screws and washers (diameter ≥ 15.8 mm) for FB1 and FB2 mounting.
Ä Use M6 corrosion-proof screws and washers (diameter ≥ 13.2 mm) for TB1 mounting.
2 PLANNING
2.3 MOUNTING OPTIONS
TYPE OF
INSTALLATION MODULE POINT MOUNTING SYSTEM LINEAR MOUNTING SYSTEM
INSTALLATION
WITH INSERTION
PROFILES Q.PEAK DUO L-G8.X
NOT PERMITTED
TRACKER
INSTALLATION
ON MOUNTING
POINTS Q.PEAK DUO L-G8.X
TRACKER
INSTALLATION
WITH CLAMPS Q.PEAK DUO L-G8.X
IP1 IP2
2 PLANNING
2.3 MOUNTING OPTIONS
TB1
840
EN
TC1
830 - 890
EN