(UK). +44(0)333 444 1280
www.pyronix.com
Pyronix Limited, Pyronix House, Braithwell Way, Hellaby, Rotherham, S66 8QY, UK
EN50131-1:2006 + A2:2017
EN50131-3:2009
EN50131-5-3:2005 +A1:2008
PD6662:2017
Security Grade (SG) 2
Environmental Class (EC) II
EN
Status LEDs
Ready (amber)
No inputs are active. The
control panel is ready to be armed.
Alarm (red)
An alarm activation has occurred.
Tamper (red)
A tamper activation has occurred.
Fault (amber)
The control panel has detected a
fault. If flashing, the Engineer Menu
has been accessed.
Disarmed (green)
The control panel has been
disarmed.
Wireless LED Keypad
Partcode: LEDP/R-WE
Doc SAP: 102022147-01
1.1
Product information
Applies to electrical products sold within the European community. At the end of the electrical product’s life, do
not dispose of it with household waste. Where possible, recycle the product. Check with your Local Authority or
retailer for recycling advice in your country.
Warranty
This product is sold subject to our standard warranty conditions and is warranted again
defects in workmanship for a period of two years. In the interest of continuing care and
design, Pyronix Ltd reserves the right to amend specifications without giving prior notice.
For more information please visit https://www.pyronix.com/terms-conditions-sales/
Proximity reader
The proximity reader is located to the left of the output LEDs. When a promixity tag is presented,
a ‘beep’ should be heard from the keypad.
1. Installation
Please follow steps 1.1 through 1.5 to install keypad to surface. Step 1.6 can either be done at the
start or at the end.
Please note:
Keypads/proximity readers should not be mounted on a metal surface, or be located
within 1m of another proximity reader, loudspeakers and/or any equipment using >100V; as the
tag reader response will degrade.
2. PCB layout and battery
To avoid damage to internal components, touch an earthed metal conductor to dissipate any
static electricity. With the case open, connect the battery leads to the battery connector port and
seat securely in the battery holder. When replacing the battery, disconnect the battery connector
and pull the ribbon to dislodge the battery. Dispose of old batteries in accordance with your local
regulations. Replace only with 1 x BATT-ES1 SAP: 361300030.
See diagram for the location of the tamper spring.
3. Learning the keypad
To learn the keypad, put the control panel in learning mode, ready to pair with the keypad. Press
and hold the ‘learn button’ for at least 5 seconds then release. Whilst holding, the LEDs will cycle
and when released, the ‘disarmed’ LED will flash to indicate a successful pairing. If all LEDs stay lit,
the procedure failed and must be tried again. To enable the wireless keypad, please refer to the
control panel programming guide.
4. Output control
Press
d
then enter Master Manager code.
Keys 1 to 4 will light up green to indicate this has been done correctly.
Press the keys to toggle the outputs on and off.
The LED of the respective output will illuminate when the output is on and will extinguish when
the output is off.
Press
x
to exit.
Specifications
Device colour
White and black
Casing
3mm ABS plastics
Dimensions (W x H x D)
168 x 121 x 34mm
Tamper switches
Front and rear
Battery
1x BATT-ES1
(CP405050-P2, 3.0V, 4700mAh LiMnO2)
Low battery threshold
2.4V
Transmission
868MHz FM tranceiver narrow band
Fully encrypted rolling code
Storage temperature
-10°C to +40°C
Operating temperature
-10°C to +40°C
EN50131 Certified
Grade 2
Output
on
Output
off
&
168mm
121mm
34mm
290g
>5s
1.2
1.3
1.4
1.5
1.6
2
3
4
