PYROMANIA GAS4120-B Feature Manual Download Page 12

 

 

PERATION INSTRUCTIONS                                                                                  11 

_____________________________________________________________ 

 

LIGHTING

 

USING THE IGNITOR: 

 

Read and understand all pre-use and operating instructions before lighting. 

 

Make sure that the burner control knob is in the “OFF” position 

 

It using propane, slowly open the valve on the propane cylinder 

 

While pushing the ignitor button with one hand, use your other hand to push to turn and hold the control 

knob to the “IGNITE” position.  

 

 

 

 

 

 

 

 

 

 

Keep the burner control knob pressed in for 15-30 seconds after ignition. 

 

If ignition does not occur in 30 seconds, turn the knob to the “OFF” position, wait 5 minutes until the gas 

clears and repeat the lighting procedure. 

 

After lighting, turn the control knob counter-clockwise to adjust the flame to the desired height (the  

recommended height is 8” to 13”). 

 

 

 

 

 

 

 

 

USING A LONG MATCH OR BBQ LIGHTER: 

1.

 

Make sure that the burner control knob is in the “OFF” position 

2.

 

Prior to lighting, clear some lava rock away from the burner ring with a garden trowel to gain access to the 

burner holes. 

3.

 

Wearing heat resistant gloves, position the flame of the match or BBQ lighter near the exposed burner holes. 

Do not lean over the fire table while lighting. 

4.

 

Press, turn and hold the control knob counter-clockwise to “IGNITE”. 

5.

 

Keep the burner control knob pressed in for 15-30 seconds after ignition. 

6.

 

After lighting, turn the control knob counter-clockwise to adjust the flame to the desired height. 

 

SHUTTING OFF 

 

1.

 

Turn the control knob clockwise to the IGNITE position. 

2.

 

Push and turn the knob clockwise to the OFF position. 

 

NOTES 

 

Do not attempt to put a fabric cover on or move this appliance until it has completely cooled down. 

It is recommended to shut-off the gas supply when the appliance is not being used for an extended period of time. 

Summary of Contents for GAS4120-B

















Reviews: