www.PyleUSA.com
2
www.PyleUSA.com
3
For the best results and the satisfaction from your new unit, please read
this manual thoroughly, and retain it for future reference.
OPERATION AND MAINTENANCE
·
Do not use the device in the vicinity of a TV, radio, stereo equipment, mobile
phone, or other electric devices. Otherwise, the device, TV, or radio may
generate noise.
·
In order to prevent the possibility of panel disfiguration, unstable operation, or
damage to the internal components. Do not expose the device to excessive dust
or vibration, or extreme cold or heat (such as in direct sunlight, near a heater, or
in a car during the day).
·
Do not place vinyl, plastic or rubber objects on the device, since this might
discolor the panel.
·
When cleaning the device, use a dry and soft cloth. Do not use paint thinners,
solvents, cleaning fluids, or chemical impregnated wiping cloths.
·
Condensation can occur in the device due to rapid, drastic changes in ambient
temperature when the device is moved from one location to another, or air
conditioner is turned on or off. For example, using the device while condensation
is present can cause damage. If there is reason to believe that condensation
might have occurred, leave the device for several hours without turning on the
power until the condensation has completely dried out.
·
Avoid setting all controls to their maximum. Depending on the condition of the
connected devices, doing so may cause feedback and may damage the speakers.
·
When turning on the power in your audio system, always turn on the power
amplifier LAST, to avoid speaker damage. When turning the power off, the power
amplifier should be turned off FIRST for the same reason.
PRECAUTIONS WHEN USING THE USB 2.0 AND 5V DC TERMINALS
When connecting the USB2.0 connector to computer, please must abide by
following points. If not, it may cause computer crash, breakdown, or losing
data. If the computer or mixer crash, please restart the application software
or computer operating system, or disconnect the mixer, then power on again.
·
Use an USB cable. USB 3.0 cable cannot be used.
·
Before connecting the computer to the USB 2.0 terminal, exit from any power-
saving mode of the computer (such as suspend, sleep, standby).
FUNCTION AND INTRODUCTION
1.
[MIC/LINE]
Mono input, connect the microphone, musical instrument or audio
device (CD player and so on) to the device. The sockets are supporting both
XLR and UNBALANCED 1/4"PLUG.
2.
[+48V PHANTOM]
Button/LED, when the button is turned on, the LED light is
on, provide DC+48V phantom power to XLR plug on MIC mono input. Please
turn on this button when using the condenser microphone which is powered
by a phantom power.
3.
[GAIN]
Controller, determines the basic volume of each channel, adjust them
for the maximum volume performance, when the volume gets too loud, the
[PEAK] LED indicator light will keep flashing.
4.
[HIGH]
Treble tone controller, adjust the controller to enhance or attenuate
for 15dB at 12 KHz .
5.
[LOW]
Bass tone controller, adjust the controller to enhance or attenuate for
15dB at 80Hz.
6.
[FX]
Controller, adjust the signal level from the channel to the reverberation
line. Please note, the single level will vary with the different setting of the
channel attenuator. If using the stereo channel, will mix the signals from L and
R channels, then, send it to reverberation line.
7.
[LEVEL]
Controller, adjust to balance the volume of each channels.
8. Stereo channel input, if only connect to L/(MONO) socket, the mixer will send
out the same mono signal to L and R outputs.
4
5
6
24
8
8
9
10
14
15
17
1
2
3
20
25
21
7
7 23
18 19
16
25
4
5
6
24
8
8
9
10
14
15
17
1
2
3
20
21
7
7 23
22
19
16
UNBALANCED 1/4 " PLUG