WIRING DESCRITION
10PIN CONNECTION
BROWN
Parking light wire (12v positive output) connect to parking light wire
BROWN
Parking light wire (12v positive output) connect to parking light wire
PURPLE
TACH wire (AC input) connect to TACH signal wire (coil or injector)
YELLOW/
Starter kill wire (500mA negative output) connect to starter kill
GREEN
relay.
ORANGE
Lock NC (See page 5)
WHITE
Lock COM (See page 5)
YELLOW
Lock NO (See page 5)
ORENGE/
Unlock NC (See page 5)
BLACK
WHITE/
Unlock COM (See page 5)
BLACK
YELLOW/
Unlock
NO (See page 5)
BLACK
4 PIN CONNECTION
WHITE
Switched ignition input (12v positive input) connect to ignition wire.
GREEN
Hand brake wire (negative input) connect to switched side of hand
brake switch.
BLUE
Door trigger negative input, connect to negative door switch.
ORANGE
Brake wire (positive input) connect to the switched side of the brake
pedal switch.
WIRING DESCRITION
L
e
a
rn
in
g
b
u
tt
o
n
WIRE CONNECTION GUIDE
Blue
Battery
Starter
Accessories
Ignition
Yellow
Brown
Red
White
Blac k
Ground
Blue
Orange
Brake switch(positve input)
Door trigger input negative
Green
Hand brake switch
negative input
Brown
Brown
Tach signal
(call AC input)
Pink
Siren
Antenna
Yellow
+12V
Yellow Starter wire
81a
87
86
30
85
Red
Central door
lock connection
Purple
+12v constant wire (12v positive input) connect to a 12v constant,
30 A fuse built in.
BLACK
Ground wire, important connect to a ground.
Accessories wire (12v positive output) connect to wire that controls the
heater/air conditioning fan.
YELLOW
Starter wire (12v positive output) connect to starter wire.
BROWN
gnition wire (12v positive output) connect to main ignition.
I
PINK
Siren wire connect to siren, do not require a relay if siren under 3A is used.
WIRING DESCRITION
The newest technological are integrated in our Two Way Alarm and Remote Engine Start
alarm system. They are fully programmable for your customers to have personalized
security and comfort. The ultimate in comfort and protection.
The alarm integrated in the system is a fully programmable unit with multi zone protection
such as shock sensor, starter kill output, control power locks and much more.
6PIN CONNECTION
RED
BLUE
INTRODUCTION
ALARM
(AUDI) (BENZ)100
1
2
3
2.Negative trigger
2.Negative trigger
NOTE: The system must be programmed for
4 second door lock pulses.
NOTE: The system must be programmed for
4 second door lock pulses.
To the
door
+12V
(-)
(-)
+12V
+12V
Actuator
Adding actuator
Adding actuator
NC
COM
NC
NC
NC
NC
COM
COM
COM
COM
NC
COM
NC
NC
NC
NC
COM
COM
COM
COM
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
Lock
Lock
Unlock
Unlock
+12V
+12V
Interior circuit diagram of the relay
Interior circuit diagram of the relay
1.Positive trigger
1.Positive trigger
Orange
Lock
Unlock
white
yellow
Orange/black
white/black
yellow/black
To electric
vacuum pump
(-)
(-)
DOOR LOCK WIRING DIAGRAM
Vacuum system
IMPORTANT: The installation must be complete before accessing programming
mode.
DOOR LOCK PULSE:
Some European Vehicles such as Mercedes-Benz and Audi, require longer lock and unlock
pulse to operate the vacuum pump.
Start the engine, press button and at the same time. Parking light will
turn on 0.5 second, that means 0.5 second door lock pulse selects. If the
parking light turn on 4 seconds, that means 4 seconds door lock pulse
selects.
SHOCK SENSOR:
NOTE
: When adjusting the sensor, it must be in the same mounting location that it will be
after the install is complete. Adjusting the sensor and then relocating the shock
sensor requires readjustment.
PROGRAMING
SHOCK
SENSOR
Max
ANTENNA INSTALLATION POINTS
TROUBLESHOOTING
5-10cm
5-10cm
Mainframe
Mainframe
Antenna frequency
head location
TROUBLE SHOOT
1. Siren chirp continuously cannot be
deactivating by transmitter after the
installation of the control module.
1A. Please check if the electrical outlets are mistakenly plugged
Problem with the connection
Fuse of control module blow
Is the main module matched with the transmitter?
5A. Please check the connection see page 5
.
2. When the alarm is triggered the
siren does not actives.
2A. Please check if there is something wrong with the
siren, check the connection between main unit and
siren.
3. Status LED doesn't work.
3A. See page 4
Is the LED plugged into the correct
socket?
4. Door locks operate backwards.
4A. This unit has easily-reversed lock/unlock output.
Recheck page 4
to see if you have reverse these.
5. Door locks doesn't work.
TWO WAY LCD TRANSMITTER OPERATION
1
2
3
11
12
13
14
15
4
5
6
7
8
9
10
16
1. R transmit / Receive
2. Silent mode
3. Vibration mode
4. AM
5. PM
6. Lock
7. Impact detector alarm
8. Unlock
9. Parking light
10. Door open
11. Time display
12. Successful learning indicator
13. Engine start
14. Low battery indicator
15. Trunk release
16. Engine running
F
TRANSMITTER OPERATION
FUNCTION
PRESSING BUTTON
ACTIVATION
BUTTON ARM SILENTLY
ARMING NO
CHIRP
Press once
System armed and doors locked
without chirp
ANTI CAR-
HIJACKING
Press then
press
while driving.
System enter anti car-hijacking mode.
BUTTON
ENGINE START
ENGINE START
Press once and press
again within 5 seconds.
Send signal to start engine.
BUTTON
VIBRATION
VIBRATION
Press once
To select vibration on or off.
FUNCTION
PRESSING BUTTON
ACTIVATION
BUTTON
ARM:
ARMING
Press once System armed and doors locked with chirp.
STOP ENGINE
Press once (when engine
running with engine start).
Send signal to stop engine.
PANIC MODE
Press once after system
arm 30 seconds.
Siren chirps 2 seconds and parking light
flashing 3 times.
BUTTON
DISARM
DISARMING
Press once
Systems disarmed and doors unlocked
with 2 chirp.
DISARMING
NO CHIRP
Press once when system
arm at silently mode.
System disarmed and doors unlocked
without chirp.
TRANSMITTER OPERATION
COMMOM BUTTON USED BY 3508 TRANSMITTER
ARM & LOCK THE DOORS
DISARM & UNLOCK THE DOORS
ARM & LOCK THE DOOR SIRENTLY
ENGINE START
VIBRATION ON/OFF
ADJUST REALTIME CLOCK:
Keep press
button 8 seconds until the display show the hour flashing. Use button to
adjust hour and use button to adjust minute. When it is done, press button to exit.
NOTE:
You can exit a mode anytime by pressing the Button.
TRANSMITTER OPERATION
REPLACE THE BATTERY OF YOUR TRANSMITTER:
icon will flashing at display and you hear beeps sound.
Transmitter battery has to be change. Your two way transmitter is powered by an AAA
1.5V alkaline battery.
NOTE:
When the battery weekends, operating range will be reduced
and the back light will
dim.
When transmitter battery low,
TRANSMITTER OPERATION
Two Way Transmitter
LOCK
UNLOCK
MUTE
START
VIBRATION
T WO - W AY
FEATURES AND OPERATIONS
IGNITION LOCK:
Door locks automatically when ignition is ON and brake pedal is depressed after driving 15
seconds. Doors will unlock when ignition is turned off.
SHOCK SENSOR PRE-WARNING:
Siren chirps rapidly when shock sensor is trigger. If shock sensor is trigger for a second
time within 10 seconds, the siren will sounds for 30 seconds.
ALARM AND REMOTE STATER INTERACTION:
Your remote engine start can be active even if the alarm system is armed or disarmed,
arm or re-arm the alarm when engine is running via remote starting.
REMOTE ENGINE START:
Press
button on the transmitter, siren will chirp once and parking light will turn on, within
5 seconds press button again engine will start 2 seconds later. Parking light will flash as
long as the engine is running 10 minutes. If the engine refused to start, the system shut off
completely. You may be experiencing a mechanical problem.
ARMING:
Arming the system will also enable the starter kill and unlock the door, if installed.
PASSIVE ARMING:
The system will automatically arm without door lock itself 30 seconds after the ignition has
been turned OFF and the last door closed.
DISARMING:
Disarming the system will also disable the stater kill and unlock the door, if installed.
SAFE REARMING:
If you disarm the system by accident and you do not open any access (door ), it will rearm
automatically after 30 seconds, unless the engine running.
STARTER KILL OUTPUT:
When the system is armed manually or via passive arming the starter kill will arm at the
same time.
PANIC MODE:
While arming mode press
button panic mode is engaged. The siren will be chirp 2
seconds and parking light will flashing 3 times.
FEATURES AND OPERATIONS
STEP1
DELETE CODE FOR CONTROL UNIT:
Press learning button at control unit until the LED at control unit (near the learning
button) turn off. System will delete all transmitter code.
STEP2
DELETE CODE FOR TWO WAY TRANSMITTER:
Press button at two way transmitter for 8 seconds until
icon at LCD display
turn off, transmitter will delete control unit code.
STEP3
CODE LEARNING:
Press learning button at control unit, LED at control unit (near the Learning button)
will flash once to enter code learning mode. Press any Button on the transmitter,
LED will turn on 0.5 second when received the transmitter code. Continuous doing
the same step for the next transmitter.
NOTE:
The transmitter supplied is already programmed to the system.
TRANSMITTER CODE LEARNING
Summary of Contents for car security system
Page 1: ......
