background image

1.3 Requirements

The following are required to install and use the Clone+™ devices:

digital satellite, cable or terrestrial receivers of Conax, Cryptoworks, Irdeto MediaGuard, 

Viaccess-coded pay-tv.

a working 

installation*

 connected to each of the digital satellite, cable or terrestrial 

receivers, 

valid subscriber card.

 

The integral parts of the complete set-up are (for satellite installation):

satellite dish, 

full band converter, 

coaxial cable for connections.

1.4 Other electronic equipment

Devices which emit radio transmission in their wireless communication may

disrupt the performance of the Clone+™ devices.

1.5 Important notes

Use only the designated power adapter and accessories approved by PYCH International

Electronics Sp. z o.o.. Using any other unsuitable power adapters and accessories which are

not approved by PYCH International Electronics Sp. z o.o. may result in damaging the unit

or severe injury.

  

   

a working installation is herewith defined as an installation in which all the devices have been 

installed properly.

1. Safety and usage information

The Clone+™ devices have been designed according to the safety standards. Before using 

this unit, make sure to read the safety and usage information as well as the User Manual.

1.1 Small children and animals

The Clone+™ devices contain small parts which may cause choking or serious injuries if 

swallowed. Keep this unit out of the reach of small children or animals.

1.2 Precautions

Keep the Clone+™ device away from rain, moisture and humidity. 

Keep the Clone+™ device away from direct sunlight, heat-generating equipment or 

strong magnetic field or its emitters or generators.

It is advised not to use the Clone+™ device during the storm. It is recommended 

to unplug the device from the mains to eliminate the risk of the electrical shock or 

short-circuit.

Do not clean the Clone+™ device with water, liquids or aerosols.

The voltage of the designated power adapter that comes with this unit is 230V AC/50-

60Hz.

Do not overload wall power outlets or extension cords, as this may result in the risk of 

fire or electrical shock.

5

Summary of Contents for Clone+


















Reviews: