background image

 

 

Page 8 / 24                 

Copyright 2017 ProVideoInstruments USA 

– All Rights Are Reserved

 

  Users should make sure the 2 ends of grounding wire well electric conducted and 

be antirust. 

  It is prohibited to use any other device as part of grounding electric circuit 

 

The area of the conduction between grounding wire and device’s frame should 

be no less than 25 mm

2

 

Chapter 3 WEB NMS Operation

 

3.1 Encoder login 

The default IP address of this device is 192.168.0.136. Connect the PC (Personal 

Computer) and the device with net cable, and use ping command to confirm they 

are on the same network segment. 

I.G.  the  PC  IP  address  is  192.168.99.252,  we  then  change  the  device  IP  to 

192.168.99.xxx (xxx can be 1 to 254 except 252 to avoid IP conflict).   

Use  web  browser  to  connect  the  device  with  PC  by  inputting  the  Encoder  & 

Modulator

’s IP address in the browser’s address bar and press Enter. 

It will display the Login interface as Figure-1. Input the Username and Password 

(Both the default Username and Password are 

“admin”.) and then click “LOGIN” 

to start the device setting. 

 

Figure-1 

Summary of Contents for VeCOAX ULTRA-HDMI-QAM-IP

























Reviews: