PVA B12-1788 Operation Manual Download Page 5

Tool Kit 

 

PVA offers standard tool kits for all dispensing valves. The tool kit for the 

FCM100 is part number 

B12-1986

, which includes all necessary tools and lubricating 

grease to perform maintenance on this dispense valve: 

B12-1986

 Includes: 

 

Qty 

Part Number 

Description 

0266244 

8” Adjustable Wrench 

26563 

3/32” Allen Key 

26561 

5/64” Allen Key 

26559 

1/16” Allen Key 

5516A18 

Tweezers 

B62-0752 

2.5cc Mineral Oil Lubrication Kit 

B62-2048 

2.5cc Silicone Lubricant 

9570K71 

Hook and Pick Set 

0266255 

Pliers 

53085A61 

Soft Plastic Covers for Pliers 

PB135/2 

Micrometer Screw Driver, #2 

PT17184 

Micrometer Adjustment Wrench 

MM115 

Removable Thread Locker 

 

Operation 
 

Refer to assembly drawing 

112-2420

 for part reference numbers.

 

 

1)

 

Plumb up the valve as outlined above in the 

Setup

 procedures. 

2)

 

Regulate the air pressure operating the valve between 60-100psi. 

3)

 

Making sure that the valve is not aimed toward anyone, cycle the valve several 
times.  When the valve is cycling, the piston can be heard hitting the micrometer 
adjustment, and the needle (3) can be seen going up and down in the center.  If the 
valve is not cycling properly, refer to the 

Troubleshooting 

section. 

4)

 

When the fluid delivery system is connected to the valve, pressurize the material 
to be dispensed. 

5)

 

Once again, cycle the valve open to purge. Fluid should begin to dispense from 
the tip of the valve, continue dispensing until all air is removed. 

6)

 

Check fluid connection and packing nut (6) for leaks. If the valve is leaking, refer 
to the 

Troubleshooting

 section. 

7)

 

Turn the micrometer adjustment (11) until the desired flow rate is achieved.  
Turning the adjustment clockwise toward zero will decrease the material flow rate 
and counter-clockwise will increase the material flow rate.  If the micrometer 
adjustment is turned all the way down to zero, it will stop fluid flow entirely. 

8)

 

Once the micrometer setting is determined, the collar (E) on the micrometer (11) 
can be turned clockwise to lock the adjustment. 

 

Note: Refer to 

Troubleshooting

 section for any problems. 

Summary of Contents for B12-1788













Reviews: