PUREGLOW XPG170 Installation And Maintenance Instructions Manual Download Page 1

 

 
 
 
 

Installation and Maintenance Instructions 

 

XPG170 Electric Fires 

 

PLEASE READ THESE INSTRUCTIONS CAREFULLY AND 

RETAIN FOR FUTURE REFERENCE 

 

Your PUREGLOW electric fire has been made with great care. Here are some instructions 

including cleaning and maintenance, which will help you keep your fire in good condition 

for many years. If you experience any parts or service problems contact either your 

retailer or PUREGLOW LIMITED. 

 

This appliance is not intended for use by persons (including children) with reduced 

physical, sensory or mental capabilities, or lack of experience and knowledge, unless they 

have been given supervision or instruction concerning use of the appliance by a person 

responsible for their safety. Children should be supervised to ensure that they do not play 

with the appliance. 

 

This is an amendment to the standard and now applies to all EN60335 items. 

 
 
 

PUREGLOW LIMITED 

Stour Vale Road 

Lye, Stourbridge, DY9 8PP 

Telephone: +441384 893060   

Fax: +441384 897728 

Email: [email protected] 

Web: www.pureglowltd.co.uk

 

Summary of Contents for XPG170

















Reviews: