8
9
UNPACKING YOUR MINI-CLASSIC
Your Pure Water Mini-Classic water purification system is
shipped to you in a durable carton. Carefully remove the con-
tents from the box.
The Pure Water Mini-Classic carton contains:
•
The Pure Water Mini-Classic distiller.
•
Food-grade plastic container and lid.
•
Filter kit.
•
Owners Manual and Warranty Card.
•
Power Cord (Not included in 240 Volt machines).
If these are not present, please look for the Quality Assurance
Inspection Slip and note the name of the inspector. Call your
Dealer or Distributor; or, in the event you can’t reach them,
contact Pure Water, Inc. Customer Service Department at 800-
875-5915 (outside the USA, please call 402-467-9300).
N o t e
N o t e
N o t e
N o t e
N o t e
: Save the box and packing materials for future use in the
unlikely event your Mini-Classic should require service work.
FIRST TIME START-UP
Starting the unit for the first time:
1.
Open the door (5) and remove the boiling chamber (1) by
pulling on the handle.
2. Remove the lid (4) by turning the black lid knob counter-
clockwise and moving the lid (4) side to side and lift out.
3. Fill the boiling chamber (1) with tap water until the water
touches the bottom of the water level indicator (2). DO
NOT overfill.
4. Replace the lid (4) on the boiling chamber (1). Turn the
black lid knob clockwise and tighten firmly, ensuring a
good seal. DO NOT overtighten.
5. Push the boiling chamber (1) into the left side of the
distiller until it fits snug and the element prongs plug into
the controller.
6. Close the door.
N o t e
N o t e
N o t e
N o t e
N o t e
: DO NOT install the post filter at this time. Keep the first
batch of distilled water for soaking the post filter.
First Time Start-Up Continued...
First Time Start-Up Continued...
First Time Start-Up Continued...
First Time Start-Up Continued...
First Time Start-Up Continued...
7. Put the drinking water container in place.
8. Plug the power cord into the back of the machine and then
into the electrical source.
9. Turn the power switch (11) to START .
10. Allow the unit to operate until it automatically shuts off
(approximately 4 hours).
11. Keep the first batch of distilled water for soaking the post
filter as described in the next section, but do not drink.
12. Replace the drinking water container (10) to the distiller.
NORMAL OPERATION
1.
Ensure that the boiling chamber is cool.
2. Open the door (5) and remove the boiling chamber (1) by
pulling on the handle.
3. Loosen the black knob on the lid (4) and slide the lid from
side to side and lift the lid out.
4. Swirl and empty out any water left in the boiling chamber
(1) from the prior batch.
5. Fill the boiling chamber (1) with tap water until it touches
the bottom of the water level indicator (2).
6. Place the lid (4) on the boiling chamber (1). Tighten the
black lid knob firmly, ensuring a good seal. DO NOT
overtighten.
7. Push the boiling chamber (1) into the left side of the
distiller until it fits snug and the element prongs plug into
the controller. Close the door.
8. Submerge the filter (8) completely in a separate container
with
distilled
distilled
distilled
distilled
distilled
water for one minute. Remove the filter (8)
and place inside the filter housing (9).
9. Slide the filter housing (9) into the guide above the
drinking water container.
10. Be sure lid is removed from container. Put the drinking
water container (10) in place.
11. Turn the power switch (11) to START.
N o t e
N o t e
N o t e
N o t e
N o t e
: To activate the
unit, the switch must be fully depressed.
12. Allow the unit to operate until it automatically shuts off.
This will take approximately 4 hours.
CAUTION
CAUTION
CAUTION
CAUTION
CAUTION
: Never open the door during operation and never
remove the boiling chamber while the unit is operating.
